T H E R M O S PA N ® | 15 0 | |
Note to specifiers: Words in parentheses indicate frequently specified and highly recommended options. |
PART I – GENERAL | 1.08 | manufacturer’s recommendations. | | 2. Track rollers shall be case-hardened inner steel races |
1.01 | Section Includes | Warranty | |
A. Sectional overhead doors [manually] [motor] | A. Provide manufacturer’s standard SEVENYEAR | with 10-ball [2"] [3"] rollers. |
1.02 | operated with accessories and components. | | warranty against separation/degradation of the | | 3. All factory authorized attachments shall be |
Related Work | | polyurethane foam from the steel skin of the | | made at locations indicated and reinforced with |
A. Opening preparation,miscellaneous or structural | | panel under provisions of Section 01700. | | backup plates. |
| steel work, access panels,finish or field painting | | Standard manufacturer’sTENYEAR warranty | D. Counterbalance: |
| are in the scope of work of other trades and | | against cracking,splitting or deterioration due to | | 1. Springs shall be torsion type,low-stress, |
1.03 | divisions of these specifications. | | rust-through. | | | helical wound,oil-tempered spring wire to |
Reference Standards | PARTII – PRODUCTS | | | provide minimum [10,000] [25,000][50,000] |
A. | ANSI/DASMA 102-2003– American | | | [100,000] cycles of use,on continuous steel |
| National Standards Institute Specifications for | 2.01 | Manufacturer | | | [solid CRS] shaft. |
| sectional overhead doors published by Door & | A. Wayne-Dalton or approved equal | | | 2. Spring fittings and drums made of die cast, |
| Access Systems Manufacturers Association | | Thermospan 150 insulated sectional | | high-strength aluminum. |
B. | International. | | overhead doors of steel construction complete | | 3. Pre-formed galvanized steel aircraft cable shall |
ASTM A229 – Steel wire, oil- tempered for | | as specified in this section and as manufactured | 2.03 | provide a minimum of a 5:1 safety factor. |
C. | mechanical springs. | 2.02 | byWayne-Dalton Corp.,Mt.Hope,Ohio. | Operation |
ASTM A-653-9A– Steel sheet,zinc-coated | Materials | | A. Operation shall be [manual push-up] [chain hoist] |
| [galvanized] by the hot-dipped process, | A. Door Sections:Shall be of steel/polyurethane/ | | [motor] [motor with chain hoist]. |
D. | commercial quality. | | steel sandwich type construction with thermal | | Note: Manufacturer does not recommend |
ASTM D1929 – Ignition temperature test to | | break and calculated materials“R”-value of | | chain hoists or jack shaft operators on |
| determine flash and ignition temperature of | | 14.16,in accordance with industry guidelines. | | the following track applications. |
E. | foamed plastics. | | 1. | Exterior Skin:Structural quality,hot-dipped | | • 15" radius standard lift with roof |
ASTM E84-91A– Tunnel test for flame spread | | | galvanized steel, .022" minimum embossing, | | pitch less than 2:12 |
F. | and smoke developed index. | | | factory finished with baked-on polyester | | • Hi-lift less than 24" |
ASTM E330 – Structural performance of | | | primer and [white] [brown] polyester finish | | • Hi-lift between 12" – 23" with roof |
| exterior windows, curtain walls, and doors by | | | coats with [non-repeating random stucco | | pitch less than 1:12 |
G. | uniform static air pressure difference. | | 2. | texture and 1⁄4" wide pinstriping]. | | | • Low headroom track |
ASTM E413-87– Sound transmission class | | Interior Skin:Structural quality,hot-dipped, | | Special chain hoist assemblies (using a trolley |
H. | acoustical performance value = 21. | | | galvanized steel,factory-finished with a | 2.04 | rail) are available for the above track systems. |
ASTM E1332-90– Outdoor-indoor | | | polyester primer and white finish coat. | Locks |
| transmission class acoustical performance | | | Interior skin shall have two 13⁄4" roll-formed | | A. Locks shall engage the right-hand vertical track |
I. | value = 19. | | | integral struts per section. | | | and utilize [an interior side lock] |
ASTM E283-91–Air infiltration = 0.23 | | 3. Ends of section shall be sealed with [16-gauge] | 2.05 | [standard size rim cylinder]. |
1.04 | CFM/FT2 at 15MPH | | | [18-Gauge]hot-dipped galvanized steel full-height | Weatherstripping |
Quality Assurance | | | end caps. | | | A. Doors shall be equipped with factory-applied |
A. Sectional overhead doors and all accessories | | 4. Insulation:Cavity shall be filled with formed | | co-polymer joint seals between sections |
| and components required for complete and | | | in-place CFC free polyurethane core | | and vinyl“bulb” shaped astragal provided for |
| secure installations shall be manufactured as a | | | separated by a factory extruded thermal break. | | bottom section. Optional top head seal and |
B. | system from one manufacturer. | | 5. Insulated sections shall be tested by an I.C.B.O. | 2.06 | jamb seals are also available. |
Sectional overhead doors shall be tested and | | | certified laboratory in accordance with | Glazing |
| labeled certifying compliance with ASTM | | | ASTM E-84-91A and shall achieve a | 2.07 | A.Optional. |
| D1929 and ASTM E84-91A standards. | | | Flamespread Index of 10 or less,and a Smoke | Windload |
1.05 Systems Description | | | Developed Index of 210 or less. | | A. Windload – per DASMA 102-2003 and as required by |
A. Sectional Overhead Door: Type: | | 6. Insulation material shall be tested by an | | local codes. |
B. | Thermospan 150 [flush] | | | I.C.B.O. certified laboratory in accordance | PARTIII – EXECUTION |
Mounting:Continuous angle mounting for | | | withASTM D-1929 and shall achieve a | 3.01 | Installation |
| [steel] [wood] jambs [bracket mount to wood] | | | minimum Flash Ignition temperature of 734 | A. General: |
C. Operation:[manual push-up] [chain hoist] | | | degrees F, and a minimum Self Ignition | | 1. Install doors in accordance with manufacturer’s |
| [motor] [motor with chain hoist] | | | temperature of 950 degrees F. | | | instructions and standards. Installation shall be |
D. Material:Galvanized steel with polyester finish paint | | 7. Insulated sections shall be tested and meet all | | by an authorizedWayne-Dalton representative. |
E. | Insulation:Polyurethane | | | requirements of the UBC 17-5 corner burn. | | 2. Verify that existing conditions are ready to |
1.06 | Submittals | B. Track: Track design shall be [standard lift] | | receive sectional overhead door work. |
A. | Shop Drawings:Clearly indicate the following: | | [high lift] [vertical lift] [low headroom].Vertical | | 3. Beginning of sectional overhead door work |
| 1. Design and installation details to withstand | | mounting angles and brackets shall be hot-dipped | B. | means acceptance of existing conditions. |
| standard windload. | | galvanized.Track size shall be [2"] [3"].Vertical track | Install door complete with necessary hardware, |
| 2. All details required for complete operation | | shall be graduated to provide wedge type weather- | | jamb and head mold strips, anchors,inserts, |
| and installation. | | tight closing with continuous angle mounting for | | hangers,and equipment supports in accordance |
| 3. Hardware locations. | | [steel] [wood] jambs,and shall be fully adjustable to | | with final shop drawings,manufacturer’s |
| 4. Type of metal and finish for door sections. | | seal door at jambs. Horizontal track shall be | | instructions,and as specified herein. |
| 5. Finish for miscellaneous components | | reinforced with continuous angle of adequate | C. Fit,align and adjust sectional overhead door |
B. | and accessories. | | length and gauge to help prevent deflection. | | assemblies level and plumb for smooth operation. |
Product Data:Indicating manufacturer’s product | | Note: Horizontal track applies to standard lift, | D. Upon completion of final installation lubricate,test |
1.07 | data,and installation instructions. | | | high lift,low headroom and | | | and adjust doors to operate easily,free from warp, |
Delivery, Handling, Storage | | | follow-the-roof designs only. | | | twist or distortion and fitting for entire perimeter. |
A. Deliver products in manufacturer’s original | C. Hardware:Hinge and RollerAssembly: | | Note: Architect may consider providing a |
B. | containers,dry,undamaged,seals and labels intact. | | 1. Hinges and brackets shall be made from | | schedule when more than one sectional |
Store and protect products in accordance with | | | hot-dipped,galvanized steel. | | | over-head door or opening type is required. |
