12 | Horizontal Tracks/Q.I Flag Angles |
Tools: Ratchet wrench, 9/16” Socket, 9/16” Wrench, level, Step ladder |
Note: If you have Quick Install flag angles, complete this step.
To install horizontal track, place the top rail end over the top track roller of the top section. Align key slot of the bottom rail end of horizontal track with the Quick Install tab of the flag angle. Push curved portion of horizontal track down to lock in place.
WARNING
Do not raise door until horizontal tracks are secured at rear, as outlined in Step, Rear Back Hangs, or door could fall from overhead position causing severe or fatal injury.
Level the horizontal track assembly and bolt the top rail of the horizontal track to the encoun- tered slot in the flag angle using (1)
Remove the nail that was temporarily holding the top section in place, installed in step, Top Section.
Important: Failure to remove nail before attempting to raise door could cause permanent damage to top section.
Note: If an idrive® opener will be installed, position horizontal tracks slightly above level.
|
| Flagangle | |
|
|
| |
|
|
| Track bolt |
Flag angle |
|
|
|
Bottom rail |
|
|
|
of horizontal | Quick Install |
|
|
track | tab in place |
| Washer |
Quick |
|
| |
|
| Top rail of | |
Install | Tracks flush |
| |
| horizontal | ||
tab |
|
| |
Key slot |
| track | |
|
| ||
|
|
| |
|
|
| Flange hex |
Vertical | Vertical |
| nut |
|
| ||
track | track |
|
|
13 | Horizontal Tracks/F.A. Flag Angles |
Tools: Ratchet wrench, 7/16” Socket, 9/16” Socket, 9/16” Wrench, |
Note: If you have Fully Adjustable flag angles, complete this step.
To install horizontal track, place the top rail end over the top track roller of the top section. Align the bottom rail end of the horizontal track with the top of the vertical track. If you have Quick Install horizontal track, tighten the bottom rail of the horizontal track to the flag angle with (1) stud plate and (2)
WARNING
Do not raise door until horizontal tracks are secured at rear, as outlined in step, Rear Back Hangs, or door could fall from overhead position causing severe or fatal injury.
Level the horizontal track assembly and bolt the top rail of the horizontal track to the encoun- tered slot in the flag angle using (1)
Remove the nail that was temporarily holding the top section in place, installed in step, Top Section.
Important: Failure to remove nail before attempting to raise door could cause permanent damage to top section.
Note: If an idrive® opener will be installed, position horizontal tracks slightly above level.
14 | Adjusting Top Fixtures |
Tools: 7/16” Wrench, Step ladder |
Adjusting top fixture slide:
With horizontal tracks installed, you can now adjust the top fixtures. Vertically align the top section of the door with the lower sections. Once aligned, position the top fixture slide, out against the horizontal track. Maintaining the slide’s position, tighten the (2)
Reversing the top fixture slide (if needed):
NOTE: Depending on your application, you may need to reverse the top fixture slide for more adjustment, if needed, prior to securing it to the top fixture base.
Remove the top fixture slide by removing the two 1/4” - 20 x 5/8” carriage bolts, two reten- tion washers and two 1/4” - 20 flanged hex nuts. Flip the top fixture slide in the opposite direction. Loosely fasten the top fixture slide to the bracket using two 1/4” - 20 x 5/8” car- riage bolts, two retention washers and two 1/4” - 20 flanged hex nuts, as shown.
NOTE: The retention washers must be fully seated against the top fixture base to ensure the
Now follow the instructions at the top of this step “Adjusting top fixture slide:
| Short stem track roller |
Low headroom | (2) 1/4” - 20 |
horizontal track | Flange hex nuts |
Top fixture |
|
slide | Top section |
Top fixture |
|
assembly |
|
|
| Top fixture slide | |
(2) 1/4” - 20 |
| (2) Retention washers | |
|
| ||
Flange hex nuts |
| Slotted hole of top | |
|
| fixture base | |
Top fixture | (2) 1/4” - 20 x 5/8” | ||
Carriage bolts | |||
feature | |||
slide reversed |
|
15 | TorqueMaster® Spring Tube |
Tools: None |
TorqueMaster® springs come lubricated and
Bottom rail Quick Install Horizontal track
Flag angle upper slot
Vertical track
Stud plate
Bottom rail Fully | Flagangle | |
Adjustable | ||
| ||
Horizontal |
| |
track |
|
Flag angle upper slot
Vertical track
Washer
Top rail of horizontal track
TorqueMaster® spring tube
| Label |
16 | Center Bracket Bushing Assembly |
Tools: None |
Note: If you are installing the idrive® opener with your garage door, skip this step and go to your idrive® Installation Instructions and Owner’s Manual. After completing the steps up to and including, Drum Wrap Installation of your idrive® Installation Instructions and Owner’s Manual continue with Step, Rear Back Hangs, of this door Installation Instructions and
9
Please Do Not Return This Product To The Store. Contact your local
refer to your local yellow pages business listings or go to the Find a Dealer section online at