To Replace Headlight Bulb, To Replace Fuse

SERVICE AND ADJUSTMENTS

KEPS NUT

		HEX
		BOLT
	POSITIVE
	(RED)	NEGATIVE
	CABLE	NEGATIVE
	CABLE	(BLACK)
		(BLACK)
		CABLE

FIG. 28

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 29)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 29

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 30)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that hole in throttle lever and hole in plate line up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

	IDLE SPEED
PLATE	SCREW
PLATE
	THROTTLE CABLE
	CLAMP
	SCREW
	HOLE “A”
THROTTLE
LEVER	FAST

FIG. 30

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE T H E F A C T O R Y H I G H S P E E D S E T T I N G C A N B E DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

179347 specifications

The Weed Eater 179347 is a versatile tool designed for efficient yard maintenance, catering to both residential and professional users. This string trimmer boasts a powerful engine that provides the reliability needed for tackling tough grass and weeds, making it an essential addition to any landscaping arsenal.

One of the standout features of the Weed Eater 179347 is its lightweight design. Weighing in at just over 10 pounds, it allows users to maneuver easily around their lawns, gardens, and other landscape areas without undue fatigue. The balanced build ensures comfortable handling, which is crucial for extended use during large trimming jobs.

The Weed Eater 179347 is equipped with a dependable 2-cycle engine that delivers impressive power and performance. This engine type not only enhances operational strength but also ensures faster cutting speeds, making it easier to handle dense growth. The trimmer uses a Tap 'N Go line release system that allows users to feed more line simply by tapping the trimmer head on the ground, which adds convenience and keeps the workflow steady.

Another key characteristic of the 179347 model is its adjustable handle. Users can customize the handle height and angle to suit their preferences, improving comfort and efficiency while working on various types of terrain. This flexibility is particularly beneficial for those with larger yards or varied landscaping features.

The design also includes a protective shield that keeps debris from flying towards the user, enhancing safety during operation. The trimmer’s durable construction ensures it can withstand the rigors of frequent use while maintaining its effectiveness.

In terms of technology, the Weed Eater 179347 incorporates fuel-efficient technology that minimizes emissions while providing optimal power output. This eco-friendly feature appeals to environmentally conscious users who wish to reduce their carbon footprint while maintaining their lawns.

In summary, the Weed Eater 179347 combines power, comfort, and convenience, making it an excellent choice for anyone looking to maintain their outdoor spaces effectively. With its lightweight build, powerful engine, adjustable handle, and user-friendly line feed system, this trimmer is designed to meet the demands of both casual users and professional landscapers alike, ensuring beautifully manicured lawns with ease.

Weed Eater 179347 owner manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Models: 179347