OPERATION

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 5)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

•Place gear shift lever in neutral (N) position.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke () position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke ( ) position and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke () position until the engine runs roughly, then move throttle control to fast position. This may require an engine warm-up period from several seconds to several minutes, depending on the tem- perature.

•The attachments can also be used during the engine warm-up period.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

MOWING TIPS

•Mower should be properly leveled for best mowing per- formance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim- ming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 7).

FIG. 7

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by se- lecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

13

Page 12 Page 14
Page 13
Image 13
Weed Eater 188313 manual Mowing Tips, To Start Engine See Fig
Page 12 Page 14

188313 specifications

The Weed Eater 188313 is a highly regarded string trimmer designed for both homeowners and professionals seeking a reliable tool for maintaining pristine lawns and gardens. Built for ease of use and efficient performance, the 188313 boasts a range of features and technologies that set it apart in the competitive market of outdoor power equipment.

At the heart of the Weed Eater 188313 is its powerful, easy-start engine that provides impressive cutting capabilities without the hassle of traditional pull-start systems. This efficient engine is designed to tackle tough overgrowth while being lightweight enough to reduce user fatigue during extended tasks. The balanced design of the trimmer ensures comfort and stability, allowing users to maneuver with precision.

One of the standout features of the 188313 is its innovative cutting head technology. The trimmer is equipped with a bump feed system, enabling users to easily advance the cutting string with a simple bump on the ground. This feature not only increases productivity but also ensures that the user can maintain an uninterrupted workflow without frequent pauses to reload the string.

The Weed Eater 188313 also incorporates a dual-line cutting system, which effectively doubles the cutting width compared to single-line units. This means that users can cover more ground in less time, making the trimmer ideal for larger properties or extensive landscaping tasks. The dual-line system is designed for durability, enabling it to withstand the rigors of regular trimming without frequent replacements.

Moreover, safety is a priority with the Weed Eater 188313, which features a protective guard that shields the operator from debris while trimming. The ergonomic handle provides a firm grip, enhancing control and reducing the risk of accidents during operation.

The lightweight materials used in constructing the 188313 ensure that it is easy to transport and maneuver, appealing to those who require a portable solution for their lawn care needs. Its compatibility with various attachments also allows for versatility, enabling users to switch between tasks, such as edging and brushing, effortlessly.

In summary, the Weed Eater 188313 is a robust string trimmer that combines power, efficiency, and user-friendly features. With its advanced cutting head technology, lightweight design, and commitment to safety, it stands as an excellent choice for anyone looking to maintain their outdoor spaces effectively. Whether you are an occasional gardener or a dedicated professional, the Weed Eater 188313 provides the performance and reliability required for a well-manicured lawn.
Top Page Image Contents