1. Locate the decal on the handlebar. This decal includes two arrows. Position the handlebar on the mounting bracket be- tween these arrows.
2. Position the bracket cover over the han- dlebar. Again make sure the handlebar is between the arrows.
3. Insert screws and hand tighten only.
These screws will be tightened later. | ||||||||||||
Bracket Cover |
|
|
|
|
|
| Screw | |||||
|
|
|
|
|
| |||||||
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
| |||||
Mounting |
|
|
|
|
| Handlebar | ||||||
|
|
|
|
|
|
|
|
|
|
| ||
Bracket |
|
|
|
|
|
|
| |||||
ATTACHING THE CONTROL HANDLE TO THE HANDLEBAR
NOTE: Make sure the wire going to the con- trol handle is routed below the tube and re- mains on the right side of the handlebar and the tube.
1.Remove screw from control handle. Screw
Screw Hole
2.Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the right side of your waist.
NOTE: A
3.Adjust the strap, allowing the hook to be about 6 inches below the waist.
4.Fasten the strap hook to the clamp located between the foam grip and the mounting block and lift the tool to the operating posi- tion.
CONFIGURING YOUR UNIT
You can configure your unit using a cutting head for grass and light weeds, or a brush blade for cutting saplings and similar size ma- terial. Go to the section for the desired configuration and follow the instructions for assembling your unit.
ASSEMBLY INFORMATION -
TRIMMER HEAD
TRIMMER
HEAD
2.Slide handle onto the right side of the han- dlebar and align the screw hole.
3.
NOTE: Make sure the control handle is on the right side of the unit as shown in the il- lustration below, and the ON/OFF switch is lo- cated on the top of the control handle.
4.Adjust the handlebar to the proper position and tighten the two screws you left loose during handlebar assembly. Make sure these screws are securely tightened.
5.After attaching the control handle and tightening the handlebar, route the wire from the control handle through the slit in the bottom of the foam grip.
Foam Grip
Slit Wire
ASSEMBLY OF SHOULDER STRAP
WARNING: Proper shoulder strap and handlebar adjustments before starting the en- gine are required.
1.Try on shoulder strap and adjust for fit and balance before starting the engine or begin- ning a cutting operation.
NOTE: Remove the blade and metal shield before attaching the plastic shield and trimmer head. To remove blade, push in locking lever and hold. Rotate blade nut until the locking le- ver falls into one of the grooves in the dust cup. Continue to hold the locking lever. This will keep the shaft from turning while loosening the blade nut. Remove blade nut by turning clock- wise. Release locking lever. Remove both washers and blade. To remove metal shield, loosen and remove the four mounting screws. See ATTACHING THE METAL SHIELD and INSTALLATION OF THE METAL BLADE for illustrations. Be sure to store all parts and in- structions for future use.
ATTACHING THE PLASTIC SHIELD AND TRIMMER HEAD
WARNING: The shield must be prop- erly installed. The shield provides partial protec- tion from the risk of thrown objects to the opera- tor and others and is equipped with a line limiter which cuts excess line to the proper length. The line limiter (on underside of shield) is sharp and can cut you.
1.Remove wing nut from shield.
2.Insert bracket into slot on shield.
3.Pivot shield until bolt passes through hole in bracket.
4.Tighten the wing nut securely.
5
