MUFFLER AND SPARK ARREST- ING SCREEN

WARNING: The muffler on this prod- uct contains chemicals known to the State of California to cause cancer.

As your unit is used, carbon deposits build up on the muffler and spark arresting screen. For normal homeowner use, however, the muffler and spark arresting screen will not re- quire any service. After 50 hours of use, we recommend that your muffler be serviced or replaced by your authorized service dealer.

REPLACE SPARK PLUG

Replace the spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0.025 inch (0.6 mm). Igni- tion timing is fixed and nonadjustable.

1.Twist, then pull off spark plug boot.

2.Remove spark plug from cylinder and dis- card.

3.Replace with Champion RCJ-6Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench.

4.Reinstall the spark plug boot.

SERVICE AND ADJUSTMENTS

LINE REPLACEMENT

1.Remove spool by firmly pulling on tap button.

2.Clean entire surface of hub and spool.

3.Replace with a pre-wound spool, or cut two lengths of 12-1/2 feet of 0.080″ (2 mm) di- ameter WEED EATER brand line.

WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

4.Insert ends of the lines about 1/2 inch (1 cm) into the small holes on the inside of spool.

Spool

Small

Holes

Line exit holes

Line in Notch

Line in Notch Hub

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.

6.Push the lines into the notches, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the lines into the the exit holes in the hub as shown in the illustration.

8.Align the notches with the line exit holes.

9.Push spool into hub until it snaps into place.

10.Pull the lines extending outside of the hub to release the lines from the notches.

CARBURETOR ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head will be spinning during this procedure. Wear your protective equipment and observe all safety precautions.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is re- leased.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while running and making ad- justments. Keep all parts of your body away from the cutting attachment and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust speed until engine runs without stalling (idle speed too slow).

S Turn idle speed screw clockwise to in- crease engine speed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed.

Idle Speed Screw

Air Filter Cover

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1--800--554--6723.

8

Page 7 Page 9
Page 8
Image 8
Weed Eater 545137264 Service and Adjustments, Muffler and Spark ARREST- ING Screen, Replace Spark Plug, Line Replacement
Page 7 Page 9

FX26S, 545137264 specifications

The Weed Eater 545137264, FX26S is a versatile and robust string trimmer designed to meet the demands of both residential and professional users. This powerful tool is engineered for efficiency, precision, and comfort, making it an essential addition to any landscaping arsenal.

One of the standout features of the FX26S is its reliable 26cc 2-cycle engine. This engine balances power with fuel efficiency, enabling users to tackle dense grass and overgrown weeds with ease. The trimmer’s high-speed rotation allows for swift cutting capabilities, ensuring a clean and precise finish to any garden area. Additionally, the engine is designed to offer easier starting, reducing frustration for users and allowing for more time spent on the task at hand.

The FX26S also incorporates a lightweight design, weighing in at just under 10 pounds. This feature enhances user maneuverability, letting operators navigate around tight corners and intricate flower beds without strain. The adjustable D-handle and shoulder strap provide extra comfort and balance, further enhancing user experience during prolonged use.

Equipped with an innovative dual-line cutting system, the Weed Eater FX26S allows for a wider cutting swath, maximizing efficiency. The automatic line feed ensures that the trimmer maintains optimal line length, reducing downtime for line adjustments. This ergonomic approach to design makes it well-suited for tackling larger areas without continuous interruptions.

One of the technological highlights of the FX26S is its anti-vibration system. This feature minimizes hand fatigue, making it feasible to work for longer periods without discomfort. The trimmer is also easy to assemble and disassemble, facilitating quick storage and transportation.

The Weed Eater 545137264, FX26S is built with durability in mind. Its sturdy construction and quality materials ensure that the unit can withstand the rigors of frequent use, whether for residential yard work or professional landscaping. Furthermore, the trimmer is supported by a reliable warranty, providing peace of mind for users.

In summary, the Weed Eater 545137264, FX26S supports a combination of power, comfort, and innovative features. Its efficient engine, lightweight design, dual-line system, and anti-vibration technology contribute to a user-friendly experience that enhances productivity in lawn care tasks. This trimmer is an excellent choice for anyone looking to maintain a pristine yard or tackle tough landscaping jobs.
Top Page Image Contents