REPLACING THE LINE

1.Remove spool by firmly pulling on tap button.

2.Clean entire surface of hub and spool.

3.Replace with a pre-wound spool, or cut two lengths of 12-1/2feet of 0.080! (2 mm) dia- meter Weed Eaterr brand line.

WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

4.Insert ends of the lines about 1/2 inch (1 cm) into the small holes on the inside of spool.

Spool

Small

Holes

Line exit holes

Line in Notch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Line in Notch

Hub

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.

6.Push the lines into the notches, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the lines into the the exit holes in the hub as shown in the illustration.

8.Align the notches with the line exit holes.

9.Push spool into hub until it snaps into place.

10.Pull the lines extending outside of the hub to release the lines from the notches.

BLADE REPLACEMENT

Refer to the ASSEMBLY section for blade re- placement instructions and illustrations.

CARBURETOR ADJUSTMENT

Your carburetor is equipped with limiter caps. Carburetor adjustment is a complicated task. We recommend that you take your unit to an authorized service dealer. Damage will occur if you turn the needles beyond the limiter stops.

WARNING: Perform the following steps after each use:

SAllow engine to cool before storing or trans- porting.

SStore unit and fuel in a well ventilated area

where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore unit with all guards in place. Position unit so that any sharp object cannot acci-

dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time: S Clean the entire unit before lengthy

storage.

SStore in a clean dry area.

SLightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Fol- low the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom- mended type and heat range.

SClean air filter.

S Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

S At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.

OTHER

SDo not store gasoline from one season to

another.

SReplace your gasoline can if it starts to rust.

12

Page 12
Image 12
Weed Eater BC2500 LE Replacing the Line, Blade Replacement, Carburetor Adjustment, Seasonal Storage, Fuel System, Engine

530086828, BC2500 LE specifications

The Weed Eater 530086828, BC2500 LE is a robust and efficient tool designed for homeowners and gardening enthusiasts looking to maintain their outdoor spaces with ease. This gas-powered string trimmer features a powerful 25cc two-stroke engine, which provides ample power while being lightweight and maneuverable. With its user-friendly design, the BC2500 LE is suitable for a variety of cutting tasks, from trimming grass and weeds to edging along sidewalks and garden beds.

One of the standout features of the Weed Eater BC2500 LE is its Easy Start technology. This innovative system reduces the amount of pulling force required to start the engine, allowing users to get to work quickly without the hassle of a difficult startup process. The trimmer also boasts an adjustable speed throttle that lets users control the cutting power according to the task at hand, whether they are tackling tougher weeds or performing more delicate trimming.

The design of the BC2500 LE includes a 17-inch cutting swath, which allows for efficient coverage of larger areas while still being precise enough for detailed work. This trimmer is equipped with a dual-line bump feed head, enabling users to seamlessly extend the cutting line as needed by simply tapping the trimmer head on the ground. This feature eliminates interruptions during operation, allowing for a smooth and continuous cutting experience.

Adding to its versatility, the BC2500 LE features an ergonomic handle that reduces fatigue during extended use. The lightweight design, coupled with a balanced frame, helps users navigate around obstacles without straining their muscles. Additionally, the trimmer includes a protective shield that keeps debris at bay, ensuring a safer operation.

Another noteworthy characteristic is the durable construction of the Weed Eater BC2500 LE. Built with high-quality materials, it is designed to withstand the rigors of regular use while maintaining performance over time. The trimmer also features an easy-access air filter, which simplifies maintenance and ensures optimal engine performance.

Overall, the Weed Eater 530086828, BC2500 LE is a reliable and efficient tool that combines power, comfort, and ease of use. Its features cater to a wide range of landscaping needs, making it an excellent choice for both novice users and experienced gardeners alike. Whether you need to maintain a tidy yard or tackle overgrown areas, the BC2500 LE stands ready to take on the challenge with reliability and efficiency.