HOW to Start Your Unit, Operating Position

Engine Choke Lever

ON/STOP

Switch

FULL HALF OFF

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any con- tact with the muffler. A hot muffler can cause serious burns.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move choke lever to the FULL CHOKE posi- tion.

4.Squeeze the throttle trigger fully and hold through all remaining steps.

Starter Handle

Choke

Lever

flooded. Proceed to STARTING A FLOODED ENGINE.

8.Once the engine starts, allow it to run 10 seconds, then move the choke lever to the OFF CHOKE position. Allow the unit to run for 30 more seconds at OFF CHOKE be- fore releasing the throttle trigger.

NOTE: If engine dies with the choke lever in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move the choke lever to the HALF CHOKE position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the engine runs smoothly.

3.Pull starter rope sharply until engine runs, but no more than 5 pulls.

4.Allow engine to run 15 seconds, then move the choke lever to OFF CHOKE.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of ex- cess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded.

If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING INSTRUCTIONS

It is recommended that the engine not be operated for longer than 1 minute at full throttle.

OPERATING POSITION

ALWAYS WEAR:

Eye Protection

Muffler

Long Pants

Primer Bulb

Heavy Shoes

5.Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

6.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

7.Pull starter rope sharply until engine runs, but no more than 6 pulls.

NOTE: If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE posi- tion and pull the starter rope until the en- gine runs, but no more than 6 pulls. If the engine still doesn’t start, it is probably

Cut from your right to your left.

WARNING: Always wear eye protec- tion. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury.

Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle. At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to “weld” onto the spool.

Always release the throttle trigger and allow the engine to return to idle speed when not cutting.

530163513, FL25 LE specifications

The Weed Eater FL25 LE, model number 530163513, is designed for homeowners seeking an efficient and reliable solution for trimming and maintaining their lawns and gardens. This lightweight yet powerful gas-powered string trimmer stands out with its user-friendly features and advanced technology that make yard work a breeze.

One of the primary features of the Weed Eater FL25 LE is its 25cc 2-cycle engine. This robust engine provides ample power to handle various trimming tasks, from edging flower beds to tackling thick grass and weeds. The 2-cycle design means it’s lightweight, allowing for easy maneuverability during prolonged use without causing fatigue.

The trimmer comes equipped with a dual-line bump head, which automatically feeds the cutting line as you work. This innovative design eliminates the hassle of stopping to adjust the line manually, allowing for uninterrupted mowing. The 0.095-inch line has been specifically chosen for its durability and efficiency, ensuring a clean cut every time.

Another highlight of the FL25 LE is its straight shaft design, which extends the reach of the user. This feature is especially beneficial for trimming hard-to-reach areas, such as under bushes and along fences. The straight shaft also provides better balance and control, making it easier to navigate around obstacles.

In terms of ergonomics, the trimmer includes an adjustable handle that can be customized to the operator's preference. This adjustability ensures a comfortable grip and reduces strain on the wrist during extended use. Additionally, the lightweight construction further enhances comfort, making it a suitable choice for users of all physical abilities.

The FL25 LE is also designed with easy maintenance in mind. The air filter is easily accessible, ensuring that it can be cleaned and replaced when necessary to maintain optimal performance. Routine maintenance is essential for prolonging the lifespan of any power equipment, and the Weed Eater’s design facilitates this process.

Overall, the Weed Eater FL25 LE, 530163513, is a versatile and efficient tool ideal for maintaining a well-groomed yard. Its powerful engine, user-friendly features, and ergonomic design make it a preferred choice for homeowners who want a reliable trimmer that can handle a variety of tasks with ease. Whether you are a seasoned gardener or a new homeowner, this trimmer will assist you in achieving a professional-looking landscape.

Weed Eater 530163513 HOW to Start Your Unit, Starting a Warm Engine, Starting a Flooded Engine

Models: 530163513 FL25 LE