LINE REPLACEMENT

1.Remove spool by firmly pulling on tap button.

2.Clean entire surface of hub and spool.

3.Replace with pre--wound spool, or cut a length of 20 feet of 0.080! (2 mm) diameter Weed Eaterr brand line.

WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

4.Insert one end of the line about 1/2 inch (1 cm) into the small hole on the inside of spool.

Small

HoleSpool

Line in Notch

Hub

Line exit hole

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrow found on the spool.

6.Push the line into the notche, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the line into the the exit holebin the hub as shown in the illustration.

8.Align the notch with the line exit hole.

9.Push spool into hub until it snaps into place.

10.Pull the line extending outside of the hub to release it from the notch.

CARBURETOR ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head will be spinning during this procedure. Wear your protective equipment and observe all safety precautions.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is re- leased.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold

the unit by hand while running and making ad- justments. Keep all parts of your body away from the cutting attachment and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust speed until engine runs without stalling (idle speed too slow).

S Turn idle speed screw clockwise to in- crease engine speed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed.

Idle Speed

Screw

Air Filter

Cover

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1--800--554--6723.

WARNING: Perform the following steps after each use:

S Allow engine to cool, and secure the unit before storing or transporting.

SStore unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric

motors or switches, furnaces, etc.

SStore unit with all guards in place. Position unit so that any sharp object cannot acci-

dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time:

SClean the entire unit before lengthy storage. S Store in a clean dry area.

S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Fol- low the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom-

mended type and heat range. S Clean air filter.

8

Page 8
Image 8
Weed Eater FL25 LE, 530163513 Line Replacement, Carburetor Adjustment, Seasonal Storage, Fuel System, Engine

530163513, FL25 LE specifications

The Weed Eater FL25 LE, model number 530163513, is designed for homeowners seeking an efficient and reliable solution for trimming and maintaining their lawns and gardens. This lightweight yet powerful gas-powered string trimmer stands out with its user-friendly features and advanced technology that make yard work a breeze.

One of the primary features of the Weed Eater FL25 LE is its 25cc 2-cycle engine. This robust engine provides ample power to handle various trimming tasks, from edging flower beds to tackling thick grass and weeds. The 2-cycle design means it’s lightweight, allowing for easy maneuverability during prolonged use without causing fatigue.

The trimmer comes equipped with a dual-line bump head, which automatically feeds the cutting line as you work. This innovative design eliminates the hassle of stopping to adjust the line manually, allowing for uninterrupted mowing. The 0.095-inch line has been specifically chosen for its durability and efficiency, ensuring a clean cut every time.

Another highlight of the FL25 LE is its straight shaft design, which extends the reach of the user. This feature is especially beneficial for trimming hard-to-reach areas, such as under bushes and along fences. The straight shaft also provides better balance and control, making it easier to navigate around obstacles.

In terms of ergonomics, the trimmer includes an adjustable handle that can be customized to the operator's preference. This adjustability ensures a comfortable grip and reduces strain on the wrist during extended use. Additionally, the lightweight construction further enhances comfort, making it a suitable choice for users of all physical abilities.

The FL25 LE is also designed with easy maintenance in mind. The air filter is easily accessible, ensuring that it can be cleaned and replaced when necessary to maintain optimal performance. Routine maintenance is essential for prolonging the lifespan of any power equipment, and the Weed Eater’s design facilitates this process.

Overall, the Weed Eater FL25 LE, 530163513, is a versatile and efficient tool ideal for maintaining a well-groomed yard. Its powerful engine, user-friendly features, and ergonomic design make it a preferred choice for homeowners who want a reliable trimmer that can handle a variety of tasks with ease. Whether you are a seasoned gardener or a new homeowner, this trimmer will assist you in achieving a professional-looking landscape.