Weed Eater SB180, SB30, 530088756 Maintain Your Unit Properly, Preparation, Blower Tube Assembly

Models: 530088756 SB30 SB180

1 6
Download 6 pages 50.98 Kb
Page 3
Image 3
MAINTAIN YOUR UNIT PROPERLY

MAINTAIN YOUR UNIT PROPERLY

DHave all maintenance other than the rec- ommended procedures described in the

Operator’s Manual performed by your Service Dealer.

D Disconnect spark plug before performing maintenance except for carburetor adjust- ments.

D Use only recommended WEED EATER replacement parts; use of any other parts may void your warranty and cause dam- age to your unit.

DEmpty the fuel tank before storing the unit.

Use up fuel left in carburetor by starting the engine and letting it run until it stops.

DDo not use any accessory or attachment other than those recommended by the manufacturer for use with your unit.

DDo not store the unit or fuel in a closed area where fuel vapors can reach sparks or an

open flame from water heaters, electric motors or switches, furnaces, etc.

DStore in a dry area out of reach of children.

SPECIAL NOTICE: For users on U.S.

Forest Land and in some states, including California(Public Resources Codes 4442 and 4443), Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington: Certain in- ternal combustion engines operated on for- est, brush, and/or grass covered land in the above areas are required to be equipped with a spark arrestor, maintained in effective working order, or the engine must be con- structed, equipped, and maintained for the prevention of fire. Check with your state or local authorities for regulations pertaining to these requirements. Failure to follow these requirements is a violation of the law. This unit is not factory equipped with a spark ar- restor; however, a spark arrestor is available as an optional part. If a spark arrestor is re- quired in your area, contact your Authorized Service Dealer for the correct kit. The spark arrestor, blower tubes, and nozzles must be assembled to the unit to be in full compliance with the regulations.

SPECIAL NOTICE: Exposure to vibra- tions through prolonged use of gasoline powered hand tools could cause blood ves- sel or nerve damage in the fingers, hands, and joints of people prone to circulation dis- orders or abnormal swelling. Prolonged use in cold weather has been linked to blood ves- sel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or tex- ture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An antivibration sys- tem does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool.

PREPARATION

PREPARATION WARNING: If you receive your unit assembled, check each step to insure your unit is properly assembled. Follow all safety information in the manual and on the unit.

DNo tools are required for assembly.

BLOWER TUBE ASSEMBLY

D Assemble the blower tube and nozzle to the unit (turn clockwise to tighten).

Blower

Blower Outlet

Tube

Nozzle

NOTE: An optional vacuum kit is available for your unit. See your local retailer or call 1--800--554--6723 for details.

YOU MUST make sure the tubes are secure before using the unit.

Eye Protection

BLOWER

This engine is certified to operate on un- leaded gasoline. Gasoline must be mixed with a good quality 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand oil is recom- mended. (A 40:1 ratio is obtained by mixing

3.2ounces of oil with 1 gallon of unleaded gasoline). When mixing fuel follow the instructions printed on the container. Always read and follow safety rules under HANDLE FUEL WITH CAUTION in the SAFETY RULES section.

-- 3 --

Page 3
Image 3
Weed Eater SB180, SB30, 530088756 manual Maintain Your Unit Properly, Preparation, Blower Tube Assembly