To Level Mower Housing

Adjust the mower while riding mower is parked on level ground or driveway. Make sure tires are properly inflated (See side of tire for proper PSI). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•Measure distance "A" from bottom edge of mower to ground level at front corners of mower.

•To raise the right side of the mower, tighten lift link adjustment nut.

•To lower the right side of the mower, loosen lift link adjustment nut.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

Bottom Edge of	Bottom Edge of
Mower to Ground	Mower to Ground

•Recheck measurements after adjusting.

FRONT-TO-BACK ADJUSTMENT

IMPORTANT: Deck must be level side-to side.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of riding mower. Measure distance “F” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•To lower front of mower housing turn nuts “G” and “H” clockwise.

•When distance “F” is 1/8" to 1/2" lower at front than rear, tighten nut “H” against trunnion on front link.

•To raise front of mower housing turn nuts “G” and “H” counter clockwise.

•When distance “F” is 1/8" to 1/2" lower at front than rear, tighten nut “H” against trunnion on front link.

NOTE: Each full turn of "G" will change "F" by approximately about 3/8".

• Recheck side-to-side adjustment.

Nut "G"

Nut "H"

Trunnion

TO REPLACE MOWER BLADE DRIVE BELT

MOWER DRIVE BELT REMOVAL

1.Park riding mower on a level surface.

2.Set parking brake.

3.Lower mower to its lowest position.

4.Remove mandrel cover from mower deck.

5.Remove rear engine plate from unit.

6.Remove rear belt keeper from unit.

7.Carefully roll belt over the top of the mower blade mandrel.

8.Remove belt from idler pulleys.

Mower Drive Belt

Belt

Keeper

Mandrel	Idler Pulleys

9.Check idler pulleys to see that they rotate freely.

10.Remove belt from rear drive pulley.

MOWER DRIVE BELT INSTALLATION Install in reverse order following instruc- tions in "MOWER DRIVE BELT REMOVAL" section.

96024000100, 532 43 32-03, 96022000700, WE261 specifications

The Weed Eater WE261 is a robust and versatile string trimmer designed to tackle a variety of lawn care tasks with ease and efficiency. Aimed at both homeowners and landscaping professionals, the WE261 is built to handle the challenges of overgrown lawns and garden beds, providing powerful performance and reliability.

One of the standout features of the WE261 is its 26cc 2-cycle engine, which delivers ample power while maintaining a lightweight profile. This engine ensures that users can navigate through dense vegetation and thick weeds without compromising performance. The 2-cycle technology allows for efficient fuel usage, providing users with longer run times between refuels.

The WE261 is equipped with a dual line bump head, which automatically releases more line as needed. This feature enhances productivity by allowing the user to focus on trimming rather than manually adjusting the string. The .095-inch line diameter provides a thick cutting path, making it effective against stubborn weeds and tall grass.

Another significant characteristic of the WE261 is its ergonomic design. The trimmer features a padded hand grip and an adjustable handle, allowing users to customize their grip for maximum comfort and control. This is especially beneficial during extended use, as it minimizes fatigue and enhances maneuverability.

The trimmer also incorporates an easy-start technology, which simplifies the starting process. Users can enjoy quick and hassle-free starts with minimal effort required. This feature is particularly useful for those who may not have extensive experience with starting gas-powered equipment.

Durability is a key consideration in the design of the WE261. Constructed with high-quality materials, this weed eater is built to withstand the rigors of regular use. The robust build ensures that it can handle various outdoor conditions, making it a reliable option for any lawn care enthusiast.

In summary, the Weed Eater WE261 presents a combination of power, efficiency, and user-friendly features. With its strong 26cc engine, automatic dual line bump head, ergonomic design, and easy-start technology, it stands out as an exceptional choice for anyone looking to maintain a well-groomed lawn. Whether dealing with overgrown areas or simply keeping the yard tidy, the WE261 is up to the task, delivering performance that users can trust.

Weed Eater 96024000100 To Level Mower Housing, SIDE-TO-SIDE Adjustment, FRONT-TO-BACK Adjustment

Models: 96024000100 532 43 32-03 96022000700 WE261