5. | Lubricate the M10 x 178m Bolt (46). Attach the | 5 |
|
|
|
| Right and Left Backrest Frames (7, 8) to the |
|
|
| |
|
|
|
|
| |
| Frame (2) with the Bolt, two M10 Washers (41), |
|
|
|
|
| and an M10 Nylon Locknut (36). |
|
|
|
|
|
| Lubricate |
|
|
|
| Align an adjustment hole in the Right and Left |
|
|
|
|
| Backrest Frames (7, 8) with the indicated hole in |
|
|
|
|
| the Frame (2). Insert the Backrest Pin (26) | 46 |
|
|
|
| through the Frame and the Backrest Frames, and |
|
| 8 | |
| 41 |
|
| ||
| secure it with the Spring Clip (25). | 7 |
| 41 | |
|
|
|
| ||
|
|
|
|
| |
| Tighten all of the M10 Nylon Locknuts (36) |
|
|
| 36 |
| used in steps | 26 |
|
|
|
| 38mm Screws (39) used in step 4. |
|
|
| |
|
|
| 2 |
| 25 |
6. Press three 45mm Square Inner Caps (22) into the | 6 |
| 36 |
| |
| Leg Lever (9). Press a 1” Round Inner Cap (27) | 22 |
| ||
|
|
| |||
| into the indicated end of the Weight Tube (15). |
|
|
|
|
| Attach the Weight Tube (15) to the Leg Lever (9) |
| 9 |
|
|
|
|
|
|
| |
| with the M8 x 58mm Bolt (42), two M8 Washers |
|
|
|
|
| (43), the Spacer (30), and an M8 Nylon Locknut |
| 30 | 28 |
|
| (44). Press the 1” Angled Cap (28) onto the back | 22 | 45 | ||
|
|
| |||
| of the Weight Tube. | 42 |
| 43 | Lubricate |
|
|
| |||
|
|
| 43 | ||
|
|
|
| ||
|
| 15 |
|
| |
| Lubricate an M10 x 72mm Bolt (45). Attach the |
|
| 1 | |
|
|
|
| ||
| Leg Lever (9) to the Front Leg (1) with the Bolt |
| 44 |
| |
| and an M10 Nylon Locknut (36). Do not over- |
|
| ||
|
| 22 |
|
| |
| tighten the Nylon Locknut; the Leg Lever | 27 |
|
| |
|
|
|
| ||
| must be able to pivot easily. |
|
|
|
|
7. Orient the Seat (11) with the wide end on the side | 7 |
|
|
| |
| shown. Attach the Seat to the Frame (2) with four | 11 |
|
|
|
| M6 x 16mm Screws (37). |
|
|
|
|
|
| Wide End |
|
|
|
|
|
|
| 2 |
|
|
|
| 37 |
| |
|
|
| 37 |
|
|
|
| 8 |
|
|
|
