20. Wrap the Long Cable (80) under a 90mm Pulley | 20 |
|
|
|
|
|
|
|
(28) as shown. Attach the Pulley, a Cable Trap |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
(29), an M10 Washer (75), and two Finger |
|
|
|
|
|
|
|
|
Guards (110) to the Upright (3) with an M10 x |
|
| 3 |
|
| 75 |
|
|
127mm Button Bolt (56) and an M10 Nylon |
|
|
|
|
| 110 | 76 | |
|
|
|
|
| 28 | |||
Locknut (76). Note: The Bolt will be packaged |
|
|
|
|
|
|
| |
|
|
|
| 110 |
|
|
| |
separately for identification. Make sure the |
| 56 |
|
|
|
|
| |
Cable Trap and Finger Guards are oriented as |
|
|
|
|
|
|
|
|
shown. |
|
|
|
|
|
|
| 80 |
|
|
|
|
|
|
|
| |
|
|
|
|
|
| 29 |
|
|
21. Attach a Pulley Housing (94) to the indicated “U”- | 21 |
|
|
|
|
|
|
|
channel on the |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
(44) with an M10 x 128mm Button Bolt (24), two |
|
|
|
|
|
|
|
|
Pivot Bushings (74), and an M10 Nylon Locknut |
|
| 44 |
|
|
|
|
|
(76). |
|
| 74 |
| 74 |
|
| |
|
|
|
|
|
| |||
Wrap the Long Cable (80) over a 90mm Pulley |
|
| 94 |
|
| 76 |
| |
(28). Attach the Pulley inside of the Pulley |
| 24 |
|
| 76 |
|
| |
Housing (94) with an M10 x 42mm Button Bolt |
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||
(71) and an M10 Nylon Locknut (76). |
|
| 71 |
|
|
|
|
|
|
|
|
|
| 28 |
|
|
|
|
|
|
|
| 80 |
|
|
|
22. Wrap the Long Cable (80) around a 90mm Pulley | 22 |
| 80 | 76 |
|
| ||
(28). Attach the Pulley, a Cable Trap (29), an M10 |
|
|
| |||||
|
|
|
| |||||
Washer (75), and two Finger Guards (110) to the |
|
| 28 |
|
|
|
|
|
indicated M10 x 147mm Carriage Bolt (73) with |
| 110 |
|
|
|
|
| |
an M10 Nylon Locknut (76). Make sure the |
|
|
| 110 |
|
| ||
|
|
|
|
|
|
| ||
Cable Trap and Finger Guards are oriented as |
|
|
|
| 29 |
|
| |
|
|
|
| 75 |
|
| ||
shown. |
|
|
|
|
|
| ||
23. Make sure there are no resistance bars under the |
|
|
|
| 73 |
|
|
|
|
|
|
|
|
|
|
| |
Bar (not shown). Have a second person pull on |
|
|
|
|
|
|
|
|
the Long Cable (80) to create slack in the Cable. |
|
|
|
|
|
|
|
|
Insert the end of the Long Cable (80) through the | 23 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
welded tube on the indicated end of the Cross |
|
|
|
|
|
|
|
|
Tube (11) and then through the remaining Swivel |
|
|
|
|
|
|
|
|
Arm (22). Make sure the Cable is on the indi- |
|
|
| 71 | 104 |
|
| |
cated side of the welded rod in the Swivel |
|
| Rod |
|
|
|
|
|
Arm. |
|
|
|
|
|
|
| |
| 80 |
|
|
|
|
| ||
|
|
|
|
|
|
| ||
Insert the Swivel Arm (22) into the welded tube |
|
|
|
| 22 |
|
|
|
on the Cross Tube (11). Secure the Swivel Arm |
|
| 28 |
|
|
|
| |
|
| 76 |
|
|
| 11 | ||
with an M4 x 5mm Screw (104). |
|
|
|
|
|
| ||
Wrap the Long Cable (80) around a 90mm Pulley |
|
|
|
|
|
|
|
|
(28). Attach the Pulley inside of the Swivel Arm |
|
|
|
|
|
|
|
|
(22) with an M10 x 42mm Button Bolt (71) and an |
|
|
|
|
|
|
|
|
M10 Nylon Locknut (76). |
|
|
|
|
|
|
|
|
| 11 |
|
|
|
|
|
|
|
