12. Press two 1” Square Inner Caps (54) into the indi- | 12 |
|
|
|
|
|
| |
| cated end of the Backrest Frame (15). |
|
|
|
|
|
| |
| Attach a Plastic Foot (53) to the Backrest Frame |
| 14 |
|
|
|
|
|
| (15) with a #8 x 3/4” Screw (62). |
|
|
|
|
|
| |
| Orient the Backrest (14) and the Backrest |
|
|
|
|
|
|
|
| Backing (8) as shown. Attach the Backrest and |
|
|
|
|
|
|
|
| the Backrest Backing to the Backrest Frame (15) | 8 |
|
|
|
|
|
|
| with four M6 x 45mm Screws (58). |
|
|
|
|
|
| |
|
|
| 15 |
|
|
| 53 |
|
|
| 54 |
| 58 | 58 | 62 |
| |
|
|
|
|
| ||||
|
|
|
|
|
| |||
13. Insert the rod on the Backrest Frame (15) into the | 13 |
|
|
|
|
|
| |
| slot in the Seat Carriage (12). Hold the Backrest |
|
|
|
|
|
| |
| Frame vertically over the Seat Carriage and |
|
|
|
|
|
|
|
| slide the rod into the slot, as shown in the |
|
|
|
|
|
|
|
| inset drawing. |
|
|
|
|
|
|
|
|
| Rod |
|
|
|
|
|
|
|
| 15 |
|
|
|
|
|
|
|
|
|
|
|
| 15 |
| |
|
|
|
|
|
| Rod | Slot | |
|
| 12 |
|
|
|
|
| |
|
|
|
|
|
|
| 12 | |
14. | Press two 2” Round Inner Caps (57) into the top |
|
|
|
|
|
| |
14 |
|
|
|
|
|
| ||
| and bottom of the Leg Developer (19). Press two |
|
|
|
|
|
| |
| 1 3/4” Round Inner Caps (56) into the top and |
|
|
|
| Tube | 57 |
|
| bottom of the Leg Lever (7). |
|
| 76 |
|
| ||
| Lubricate a 3/8” x 2 3/4” Bolt (64) with grease. |
| 56 |
|
|
|
| |
| Attach the Leg Lever (7) to the Leg Developer | 78 |
|
|
| 64 |
| |
| (19) with the Bolt and a 3/8” Nylon Locknut (76). | Tube |
| 19 |
|
| ||
| Do not overtighten the Locknut; the Leg Lever |
| 7 |
| Lubricate |
| ||
| must be able to pivot easily. | 26 |
|
|
|
| ||
| Slide two Foam Pads (26) onto the tubes on the |
|
|
|
| 57 |
| |
| Leg Lever (7). Press two 1 1/4” Round Inner |
|
|
|
| 78 |
| |
| Caps (78) into the tubes. Repeat with the tube |
| 56 |
|
|
| ||
| on the Leg Developer (19). |
|
|
|
|
|
| |
|
| 9 |
|
|
|
|
|
|