15. Slide the Leg Developer (19) into the Bench Rail | 15 |
|
|
|
|
| |
(5). Align the hole in the Leg Developer with a |
|
|
|
|
| ||
hole in the Front Leg (6). Tighten the Bench Knob |
| 7 |
|
|
|
| |
(42) into the hole in the Leg Developer. |
| 19 |
|
|
| ||
Connect the eyebolt on the Leg Lever Cable (32) |
|
|
|
|
| ||
to the indicated side of the Leg Lever (7) with a | 65 |
|
|
|
|
| |
5/16” Nylon Locknut (65). |
|
|
|
|
| ||
|
| Eyebolt |
|
|
|
| |
|
| 5 | 32 | 42 |
|
|
|
|
| 6 |
|
|
|
| |
16. Locate the Long Cable (80). Insert one end of | 16 |
|
|
|
|
| |
the Cable through the welded tube on the indicat- |
|
|
|
|
| ||
ed end of the Cross Tube (11) and then through a |
|
|
| 80 |
|
| |
Swivel Arm (22). If necessary, use the tip of a |
|
|
| 71 | |||
screwdriver to pull the end of the Cable out of the |
|
| 11107 | ||||
Swivel Arm. Make sure the Cable is on the indi- |
|
|
|
| |||
cated side of the welded rod in the Swivel Arm. |
|
|
|
|
| 22 | |
Insert the Swivel Arm (22) into the welded tube |
|
| 28 |
|
| ||
on the Cross Tube (11). Secure the Swivel Arm |
|
|
|
| Rod | ||
with a #8 x 3/8” Screw (107). |
|
|
|
| 76 | ||
Wrap the Long Cable (80) around a 90mm Pulley |
|
|
|
|
| ||
(28). Attach the Pulley inside of the Swivel Arm |
|
|
|
|
|
| |
(22) with a 3/8” x 1 1/2” | Button Bolt (71) and a |
|
|
|
|
|
|
3/8” Nylon Locknut (76). |
| 17 |
|
|
|
|
|
17. Wrap the Long Cable (80) around a 90mm Pulley |
| Flat |
|
|
| ||
(28). Attach the Pulley and a Pulley Guard (29) to |
|
| Edge | 29 | 76 |
| |
the indicated 3/8” x 5 1/2” Carriage Bolt (73) with |
|
|
| ||||
a 3/8” Nylon Locknut (76). Make sure the flat |
|
|
|
|
| 80 | |
edge of the Pulley Guard is on the side shown. |
| 73 |
|
|
| ||
|
|
|
|
| 28 | ||
|
|
|
|
|
| ||
18. Attach a Pulley Housing (94) to the indicated “U”- | 18 |
|
|
|
|
| |
channel on the |
|
|
|
|
| ||
(44) with a 3/8” x 4” Button Bolt (24), two Pivot |
|
|
|
|
|
| |
Bushings (74), and a 3/8” Nylon Locknut (76). |
| 44 |
|
|
|
| |
Wrap the Long Cable (80) around a 90mm Pulley |
|
|
|
|
| ||
(28). Attach the Pulley inside of the Pulley |
| 76 |
|
|
|
| |
Housing (94) with a 3/8” x 1 1/2” Button Bolt (71) |
|
| |||||
and a 3/8” Nylon Locknut (76). |
| 74 |
| ||||
|
|
| 71 | 94 | 76 |
|
|
|
|
| 28 |
|
|
| |
|
|
| 74 |
|
|
| |
|
|
| 80 | 24 |
|
|
|
|
| 10 |
|
|
|
|
|
