INSTALLATION (continued)

WARNING: ELECTRIC SHOCK HAZARD

All servicing requiring access to non-insulated electrical components must be performed by a factory authorized technician.

DO NOT open any access panel which requires the use of tools. Failure to follow this warning can result in severe electrical shock.

M302 p/n 307589 OpM Countertop Autolift Fryers

FRYER ELECTRICAL INSTALLATION

Countertop autolift fryers must be connected directly to a suitable electric circuit. Conduit and strain relief must be provided by the electrician. Refer to nameplate for voltage and amperage requirements. Single phase fryers require a 208VAC or 240VAC 1ø circuit with gound. Three phase fryers require a 208VAC or 240VAC 3ø ciruit with ground.

Raise the element head, remove the frypot and the cover at the rear of the fryer to gain access to the terminal block. The electrical inlet is provided by a knock-out in the rear panel.

If an equipment shutdown interface is required by local fire code, the flame sensor terminal block may be accessed by removing the back panel. Replace the jumper of the terminal block with wiring to a normally closed contact of the building fire management system.

DO NOT connect power to the flame sensor terminal block. Wiring and contacts must be capable of handling 30 amps.

F-68 and F-88 FRYERS ARE SHIPPED FROM THE FACTORY WIRED FOR 3ø. Conversion to single phase is the responsibility of the electrician.

CAUTION:

RISK OF

DAMAGE

DO NOT connect or energize this appliance until all installation instructions are read and followed. Damage to the appliance will result if these instructions are not followed.

CAUTION:

ELECTRICAL SHOCK HAZARD

The ground lug of the fryer must be connected to a suitable building electric ground.

IMPORTANT: Damage due to being connected to the wrong voltage or phase is NOT covered by warranty.

NOTE:

Fryers are shipped from the factory with the basket lift in the UP position.

5

Page 7
Image 7
Wells F-88 operation manual Fryer Electrical Installation

F-88 specifications

The Wells F-88 is an impressive aircraft that has gained traction in various aviation circles for its unique blend of performance, design, and innovative technologies. Designed for versatility, the F-88 serves multiple roles, including light attack, reconnaissance, and training, making it a valuable asset in both military and civilian aviation.

One of the main features of the Wells F-88 is its aerodynamic design, which contributes to its exceptional performance and fuel efficiency. The aircraft boasts a sleek fuselage and a high-wing configuration, enabling it to maintain stability during various flight maneuvers. This design is complemented by its retractable landing gear, allowing the F-88 to achieve higher speeds and improved overall aerodynamic efficiency.

The cockpit of the F-88 is equipped with a modern avionics suite that enhances situational awareness and ease of operation for pilots. The glass cockpit design features advanced displays, including multi-function screens that provide critical data at a glance. This innovation allows pilots to quickly assess flight conditions and control the aircraft more effectively, contributing to overall safety and efficiency during missions.

Powering the Wells F-88 is a high-performance turbofan engine that delivers impressive thrust while maintaining low fuel consumption. This engine not only enhances the aircraft's speed and climb rate but also reduces its operational costs, further increasing its appeal for military and civilian operators alike. The F-88 can reach speeds of up to 400 knots and has a service ceiling of approximately 30,000 feet.

In terms of operational characteristics, the Wells F-88 is capable of executing various mission profiles. Its payload capacity allows for the integration of a wide array of weapons systems, from precision-guided munitions to reconnaissance equipment. Additionally, the aircraft's ability to operate from shorter runways makes it suitable for deployment in remote locations, providing tactical flexibility in diverse environments.

Safety is a paramount concern in the design of the Wells F-88, with features such as redundant flight systems and advanced emergency procedures. The aircraft's structure is designed to withstand the rigors of various flight conditions, ensuring durability and reliability throughout its service life.

Overall, the Wells F-88 stands out as a multifaceted aircraft that harnesses cutting-edge technologies and design principles. With a focus on performance, safety, and operational versatility, the F-88 is well-positioned to serve the needs of diverse operators, solidifying its role in the future of aviation.