positioned against the wall), mark on the floor where the back edge of the range will be. Place template on the floor and align side of template with the line marked on the floor. Align the back of the template with the rear wall or the line marked for the rear of the range.
Go to Step 15.
lIf range will NOT be installed against a cabinet, move range into final position. Mark on the floor along both sides of the range. If back of range will not be flush with the wall (the location of the outlet may not allow the range to be positioned against the wall), mark on the floor where the back edge of the range will be.
Place template on the floor and align sides of template with the lines marked on the floor. Align the back of template with the rear wall or the line marked for the rear of the range.
Go to step 15.
back edge of range or rear wall,
If template is not available...
l and there will be cabinets on both sides of range, mark on the floor lines that are l/2” from rear wall, 3/4” from each side of the cabinet walls and
Place
l and there will be a cabinet on one side only, move range into final position. Mark on the floor along the side of the range that is not against the cabinet. Determine the center point between the cabinet and the line drawn along the side of range. Mark lines
Place
l and there will be no cabinets against range, move range into final position. Mark on the floor along both sides of the range. Determine the center point between the lines drawn for the point. Mark on the floor a line l/2” from rear wall.
Place
Floor Damage
Contact a qualified carpet installer for the best procedure to drill mounting holes through your type carpet.
Failure to do so could cause damage to floor covering.
15 n To mount anti- tip brackets to wood floor, drill a 3/l 6”
hole, l/2” deep at each mounting hole location,
To mount
a masonry drill bit to e
drill a 3/16” hole at each mounting hole location. Tap plastic anchors into mounting holes in floor with hammer,
1m n Place brack;< on floor with small flange to front. Line up holes in
provided to fasten
Floor Damage
Keep cardboard under range when moving range.
Failure to do so could cause damage to floor covering.
17 n Move range close to final position. Remove cardboard from under range. Plug power supply cord into grounded outlet.
Carefully move range to final position. Remove storage drawer. Check that rear leveling legs are engaged in the
19.
Place rack in oven. Place level on rack, first side to side; then front to back. If the range is not level, pull the range forward until rear leveling legs are removed from the brackets. Adjust the legs up or down until range is level.
Push range back into position. Check
that the rear leveling legs are engaged in the brackets, Replace storage drawer.
20 n Push in and turn each surface unit control knob to ‘HI” position. Check the operation of the cooktop elements and indicator lights.
21 W Check the operation of the right (large) oven.
Bake element:
l Set the right oven selector control knob to ‘BAKE.”
l Set the right oven temperature control knob to 350°F. The bottom element should glow red and the right oven indicator light should be on. The top element should become hot but not glow red. The right oven indicator light goes off when oven is preheated.
Broil element:
l Set the right oven selector and oven temperature control knobs to “BROIL.” The top element should glow red and the right oven indicator light should be on.
22 n Check the operation of the left (small) oven.
Bake element:
l Set the left oven temperature control knob to 350°F. The bottom element should glow red and the left oven indicator light should be on. The top element should become hot but not glow red. The left oven indicator light goes off when oven is preheated.
Broil element:
l Set the left oven temperature control knob to “BROIL.”The top element should glow red and the left oven indicator light should be on.
4-wire electrical connection
Use this wiring method for mobile homes and whenever
2
A n Use a
unding screw
link -
B n Remove the aroundina link screw from the range frame. Save tt?e grounding screw. Bend up the grounding link so that it does not contact the range.
C w Connect the green grounding wire on the range using the grounding screw removed in Step B. The green grounding wire must be attached first and must not contact any other terminal.
silver- colored
green |
|
|
| neutral |
Insulated |
|
|
| |
|
|
| (white) wire | |
wil ‘8 |
|
|
| |
|
|
|
| |
W&L |
| |||
I | \ | A |
| |
J@+ | ’ | strain relief | ||
D n Connect the neutral (white)
wire to the center,
Be sure that
n Tighten the strain relief screws. Replace the terminal block cover.
Fn Continue installation at Step 14, Panel B.
most efficient use from your new
/ range, read your Whirlpool Use & Care \
/ Congratulations! 1
Guide. Keep Installation Instructions and Guide close to range for easy reference. The instructions will make reinstalling your Whirlpool range in another home as
