mounting

 

 

flexible

3/W’ (0.95 cm)

 

 

connector

nipple

I

3/W

(0.95 cm)

adabters

1

 

 

 

manual

 

 

pressure

shutoff

valve

 

 

regulator

All

connections

must

be wrench-tightened.

Assemble the flexible connector from the gas supply pipe to the

Electronic Ignition System - Initial lighting

Cooktop burners use electronic igniters in place of standing pilots. When the cooktop control knob is turned to the “HI”position, the system creates a spark to light the burner. This sparking continues until the burner lights.

holes

holes

pressure regulator in order: manual shutoff valve, 3/8” (0.95 cm) nipple, 3/8”

C. Lift maintop slightly and release support rod. Pull maintop forward until hinges lock. Lower maintop.

. Locate rear mountinq holes. Place one bolt and washer into each-bf the two outermost rear mounting holes that can be used. Remove cooktop from countertop cutout.

bolt \

, grooved washer

outer lip

e.Lock each bolt and washer in place using a flat washer and hex nut on the bottom side of the burner box flange.

f . Reset cooktop in countertop opening. Center the burner box in the cutout. Check that front edge of burner box is parallel to edge of countertop.

outer lip

bolt

 

 

 

, grooved

washer

\

\

 

 

 

 

flat

washer

 

 

.nut

 

-burner box

Ye Working below the countertop, slide a locking plate over the lower end of each bolt. Fasten each bolt in place with a tubular nut. The locking plate must make contact with as much of the countertop as possible. Tighten each tubular nut by hand until outer lip of burner box is snug to countertop. Do Not overtighten to prevent damage to countertop.

(0.95 cm) adapter, flexible connector, 318”

(0.95 cm) adapter, and 3/8” (0.95 cm) nipple.

19.1 Replacethe2rearburner assemblies.

110Use pipe-joint compound made

. for use with L.P. gas to seal all gas connections. If flexible

connectors are used, be certain connectors are not kinked.

shutoff valve “open” position

III n IOpen the shutoff valve in the

Igas supply line. Wait a few minutes for gas to move through the gas line.

112Use.1a brush and liquid detergent to test all gas connections for leaks. Bubbles around

connections will indicate a leak. If a leak appears, shut off gas valve controls and adjust connections. Then check connections again. NEVER TEST FOR GAS LEAKS WITH A MATCH OR OTHER FLAME. Clean all detergent solution from cooktop.

113.1

II

Plug the power supply cord into the grounded outlet.

Align notch in each drip bowl

114with.1hole in cooktop. Insert pin located in the bottom of each

burner grate in hole in cooktop. Burner grate should sit level on drip bowl.

Place control knobs on valve stems.

If your cooktop has a griddle, place flavor- generator insert in bottom of drip pan. Place grill, griddle and cover on top of drip pan.

Insert drip pan into cooktop.

115.Check1 the operation of the cooktop burners. Push in and

uturn each control knob to “LIGHT” position. The flame should light within 4 seconds. Do Not leave the knob in the “LIGHT” position after burner lights.

116After.burner lights, turn control knob to “HI”position. Check

each cooktop burner for proper flame. The small inner cone should have a very distinct blue flame l/4” (.64 cm) to l/2” (1.3 cm) long. The outer cone is not as distinct as the inner cone.

P-JIf burners need adjusting for

. proper flame, lift maintop and support with support rod. Adjust

the air shutter to the widest opening that will not cause the flame to lift or blow off of the burner. Repeat as necessary with each burner.

118Push in and turn each control

. knob to the “LIGHT” position and then to the “LO”position.

The low flame should be a minimum, steady, blue flame approximately l/8” (3 mm) long. To adjust the burner, remove the control knob and turn the adjustment screw in the center of the valve stem. Check the adjustment by running the control knob from “HI”to “LO”several times. The burner is properly adjusted when the low flame remains steady and the burner does not go out. Check each burner.

To get the most efficient use from your new cooktop, read your KitchenAid Use and Care Guide. Keep Ins talla tion Instructions and Guide close to cooktop for easy reference.

Panel D

Page 5
Image 5
Whirlpool 3189086 installation instructions Electronic Ignition System Initial lighting, Panel D

3189086 specifications

The Whirlpool 3189086 is a refrigerator water filter designed to enhance the quality of drinking water by reducing contaminants and impurities. This replacement filter is crafted to fit specific Whirlpool refrigerator models, offering seamless integration and optimal performance. The filter is part of Whirlpool's commitment to providing clean, great-tasting water for family hydration and cooking needs.

One of the main features of the Whirlpool 3189086 is its advanced filtration technology. Utilizing activated carbon and other filtration agents, it effectively reduces harmful contaminants such as chlorine, lead, and other volatile organic compounds (VOCs). This leads to improved taste and odor, ensuring that the water dispensed from the refrigerator is not only safe but also refreshing.

This filter is designed to remove up to 99% of contaminants, which is essential for maintaining high water quality. The efficacy of the filter is backed by rigorous testing, making it a dependable choice for health-conscious consumers. Additionally, the Whirlpool 3189086 adheres to NSF/ANSI standards, certifying its ability to deliver clean drinking water.

Another characteristic worth noting is the filter’s ease of installation. The design allows for a quick and tool-free replacement, ensuring that users can maintain their refrigerator's water filtration system without hassle. This feature is particularly appealing for families who prioritize convenience in their kitchen appliances.

The longevity of the Whirlpool 3189086 is another advantage. It typically lasts for up to six months or 200 gallons of water, depending on usage levels, before requiring replacement. This ensures that families can enjoy high-quality filtered water without frequent changes, adding to the overall efficiency of their household water system.

In conclusion, the Whirlpool 3189086 stands out as a reliable refrigerator water filter packed with features that promote clean and safe drinking water. Its advanced filtration technology, easy installation process, and longevity make it an essential accessory for Whirlpool refrigerator owners who value healthy hydration and enhanced water quality in their daily lives.