Product dimensions |
| Before you start... |
21" cooktop depth
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to hazards that can kill or hurt you and others. All safety messages will be
preceded by the safety alert symbol and the word “DANGER” or “WARNING”. These words mean:
You will be killed or
DANGER seriously injured if you
|
|
| ||
recessed |
|
|
| |
height |
|
|
| |
from |
|
| ||
underside |
| overall |
| |
of cooktop |
| cooktop |
| |
| width |
| ||
to support |
|
| ||
|
|
| ||
slats |
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| shipping | |
|
|
| foot | |
|
|
|
|
|
recessed
depth
30”overall height
30"
overall
width
don’t follow instructions.
You can be killed or
WARNING seriously injured if you don’t follow instructions.
All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
Important: Observe all governing codes and ordinances.
Proper installation is your responsibility. Have a qualified technician install this range.
Range location should be away from strong draft areas, such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.
Recessed installation area must provide complete enclosure around the recessed portion of the range.
Electrical ground is required. See “Electrical requirements.”
Cabinet opening dimensions
IMPORTANT: Some cabinet and building materials are not designed to withstand the heat produced by the oven for baking and
Countertop preparation:
Front edges: You may need to shave or cut the trim of formed or metal
If countertop thickness is more than
notch width to be equal both sides
If countertop extends more
cabinet
notch widthfront to be equal
both sides
|
|
| |
|
|
| |
|
| ||
|
| max |
discolor, delaminate or sustain other damage.
Range support surface MUST be solid, level and flush with bottom of cabinet cutout.
Do not seal range to side cabinets.
When installing a cooktop under existing cabinets and the installation does not meet the minimum cabinet clearances. Install a range hood above the cooktop to avoid burn hazards.
It is the customer’s responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA
70 — latest edition**, and all local codes and ordinances.
13" max. upper | ||||
countertop | ||||
cabinet depth | ||||
thickness | ||||
|
|
|
|
For minimum clearances to the top of cooktop see Note.*
wall |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| max. |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| ||||||
| 25" countertop |
|
|
|
|
|
| ||||||
| depth |
|
|
|
|
|
| ||||||
| 24" lower |
|
|
| cabinet | ||||||||
floor | cabinet depth |
|
|
| front | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Top view of cabinet cutout
1/4"
radius both corners
top of
countertop to support slats
Install a
Mobile home installation
The installation of this range must conform to the Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280); or when such standard is not applicable, the Standard for Manufactured Homes Installations (Manufactured Home Sites, Communities and Setups), ANSI A225.1/NFPA 501A, or with local codes.**
When this range is installed in mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.
Tools needed:
1/2" dia.
Side view of cabinet cutout
router bitPhillips screwdriver
*Note: 24" min. when bottom of wood or metal cabinet is protected by not less than 1/4" flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" stainless steel, 0.024" aluminum or 0.020" copper.
30" min. clearance between the top of the cooking platform and the bottom of an unprotected wood or metal cabinet.
Copies of the standards listed may be obtained from:
**National Fire Protection Association Batterymarch Park
Quincy, Massachusetts 02269
Top of countertop |
|
|
|
| |
|
|
| |||
Note: countertop |
|
|
| opening width |
|
must be level |
|
|
| ||
across front and |
|
|
| opening is | |
front to back. |
|
| recommended, | ||
|
|
|
| if available. | |
|
|
|
|
|
|
Locate electrical | 7/8" min. |
| ||
supply junction | required | top of | 36" overall | |
box on cutout | between | counter- | ||
countertop | ||||
floor or on rear | cutout and | top to | height | |
wall (shown) | cabinet door | bottom | ||
near floor line. | or hinge. | of cabinet |
| |
|
| cutout |
|
Parts supplied:
2 screws | 2 door removal pins |
Front view of cabinet cutout
Page 1