Do Not remove shipping feet.

Electrical requirements

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path and wire gauge are in accordance with local codes.

Do Not ground to a gas pipe.

Check with a qualified electrician if you are not sure range is properly grounded.

Do Not have a fuse in the neutral or ground circuit.

Range must be connected to the proper electrical voltage and frequency as specified on the model/serial rating plate. (The model/serial rating plate is located on the oven door or on the oven frame.)

CONNECT WITH COPPER WIRE ONLY.

Models rated from 11.8 kW to 13.3 kW at 240 volts (8.9 kW to 10.0 kW at 208 volts) require a separate 40-ampere circuit.

A time-delay fuse or circuit breaker is recommended.

Connect directly to the fused disconnect (or circuit breaker box) through flexible, armored or non-metallic sheathed, copper cable (with ground wire).

Flexible armored cable from appliance should be connected directly to junction box.

Fuse both sides of the line.

A U.L.-listed conduit connector must be provided at the junction box.

Do Not cut the conduit.

Wire sizes and connections must conform with the rating of the appliance and to the requirements of the National Electrical Code, ANSI/NFPA 70 — latest edition (** See Page 1) and all local codes and ordinances.

Installation steps

D Check oven operation.

 

 

C

Grasp oven

 

 

 

 

 

 

 

frame to

 

 

 

 

 

 

 

lift range.

 

 

 

 

 

 

 

 

 

Remove

 

 

 

 

 

A

 

 

 

 

 

 

 

 

Connect

 

 

 

oven racks.

B

 

 

 

power

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

supply cable.

CRemoveshipping feet.

C Replace oven door.

DCheck cooktop operation.

CUse screws to attach range to cabinet.

CReattach side trim pieces.

ARemove side trim.

ARemovescrews. trim

ARemove oven door.

APreparation

WARNING

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

Important: Use both hands to remove oven door.

Do Not use handle or any portion of the front frame or trim for lifting.

Before moving range across floor, check that range is on shipping base or slide range onto cardboard or hardboard.

Do Not remove shipping feet at the front lower corners of range.

1.Turn power supply off. Move range close to final position.

• Remove and discard shipping materials, tape

and protective film from the range. Do Not remove shipping base or shipping feet at the front lower corners of

range. The shipping feet will protect the lower range trim until range is inserted into cabinet.

•Remove and set aside oven racks and other parts from inside oven.

Insert small end of pin here.

2.Completely open oven door. Insert small end of a door removal pin into each door hinge. Grasp door handle from the bottom and gently close door as far as it will shut. Lift slightly and grasp bottom of door with other hand. Pull door out at bottom to remove. Set door aside on protected surface.

Remove trim screw.

Pull trim out.

Pull top of trim down.

3.Remove trim screws attaching right and left side trim to range. Grasp the bottom end of trim and pull away from range. Slide top end of trim downward to remove trim from range. Take care not to scratch other surfaces with ends of trim. Set trim and screws aside on protected surface.

Page 2

Page 2 Page 4
Page 3
Image 3
Whirlpool 3191799 installation instructions Installation steps, Preparation
Page 2 Page 4

3191799 specifications

The Whirlpool 3191799 is a highly regarded replacement part designed specifically for enhancing the functionality of various Whirlpool washing machine models. This component is primarily known as a water inlet valve assembly, which plays a critical role in the water supply system of the appliance. The effectiveness and efficiency of a washing machine heavily depend on the performance of this valve, making the Whirlpool 3191799 an essential part for maintenance and repairs.

One of the main features of the Whirlpool 3191799 is its robust construction, designed to withstand the rigors of daily use. It is built with high-quality materials that ensure durability and longevity, capable of withstanding varying pressure levels and extreme conditions. This ensures that users experience less frequent replacements, ultimately saving time and money over the lifespan of the washing machine.

The Whirlpool 3191799 specifically supports both hot and cold water functions. This dual capability allows for precise temperature control during wash cycles, catering to the needs of different fabrics and load types. With this inlet valve, users can expect enhanced washing performance, resulting in cleaner clothes and more effective stain removal.

Another technological advancement found in the Whirlpool 3191799 is its efficient design that simplifies installation. The product is designed to fit seamlessly with a variety of Whirlpool washing machine models, making it a versatile choice for many users. Clear instructions are typically provided, enabling even those with minimal DIY skills to replace the valve without professional assistance.

Additionally, the water inlet valve is equipped with advanced filtration features that help prevent the entry of debris or sediment into the washing machine. This not only protects the appliance from potential damage but also ensures that the quality of water used for washing remains pure and conducive to cleanliness.

In summary, the Whirlpool 3191799 water inlet valve assembly is an essential component for maintaining optimal washing machine functionality. With its durable construction, dual-temperature capability, ease of installation, and advanced filtration, this part stands out as a reliable choice for anyone looking to enhance their Whirlpool washing machine’s performance. Investing in this component can significantly contribute to the longevity and efficiency of laundry tasks, making it a smart addition to any home.
Top Page Image Contents