BElectrical connection
WARNING
Electrical Shock Hazard
Turn power supply off before connecting wires.
Use 8-gauge solid copper wire.
Electrically ground range.
Failure to follow these instructions can result in death, fire, or electrical shock.
This range is manufactured with white (neutral) power supply wire and a
cable from
junction power supply box
red | black | |
wires | ||
wires | ||
|
white wire
white and bare |
|
| |
ground range |
|
| |
cable wires — |
| ||
factory crimped |
| ||
cable from | conduit | ||
Figure 1 | |||
range | connector |
If local codes PERMIT
connecting
cable from
junction power supply box
red | white | |
wires | ||
wires | ||
|
bare ground |
| black wires |
|
| |
wires |
|
|
Figure 2 |
| |
cable from | conduit connector | |
| range |
|
If local codes DO NOT PERMIT | If connecting to a | |
connecting | ||
conductor to neutral white | ||
wire in junction box: |
|
ground wire twisted together.
4. Make electrical connection following the steps needed for your installation.
1.Disconnect the power supply.
2.Remove the junction box cover.
3.Connect range cable to junction box through the
4.Connect the two black wires together with
5.Connect the two red wires together with
6.Complete electrical connection according to local codes and ordinances.
7.Connect the
8.Replace junction box cover.
7.Separate the
8.Connect white range cable wire to neutral (white) wire in junction box. See Figure 2.
9.Connect the bare ground range cable wire to a grounded wire in the junction box. See Figure 2.
10.Replace junction box cover.
7.Separate
8.Connect white range cable wire to neutral (white) wire in junction box. See Figure 2.
9.Connect the bare ground range cable wire to the green ground wire in junction box. Do Not connect bare ground wire to neutral (white) wire in junction box. See Figure 2.
10.Replace junction box cover.
CAttachment
Carefully push against seal area of range front frame when pushing range into cabinet.
Do Not push against outside edges.
5. Lift range into cabinet cutout using the oven opening as an area to grip. Be careful not to damage countertop.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Securely attach mounting screws to cabinet.
Reattach mounting screws if the range is moved.
Failure to follow these instructions can result in death or serious burns to children and adults.
Slide top of trim up.
Push trim into place. Replace trim screw.
7. Slide top end of each trim upward onto range side rails. Push each trim into place at bottom of trim. Use screws to attach each trim to range. Take care not to scratch other surfaces with ends of trim.
8. Replace oven racks.
oven frame hinge slot
shipping foot
To avoid damaging the countertop, lift range slightly while pushing against seal area of front frame. Push range into cabinet cutout until shipping feet almost contact cabinet. Use a Phillips screwdriver to remove screws attaching shipping feet. Remove and discard shipping feet.
Push range completely into cabinet and center range in cabinet cutout. Be careful not to damage countertop.
2 screws
6. Important: Securely fasten range to cabinet using the two screws provided. Insert the screws through holes in mounting rails. Do Not overtighten screws.
door hinge
9. Replace the oven door by inserting ends of hinges into hinge slots in range frame. Push behind each hinge so that hinges are pushed into range frame as far as they will go. Open door and remove both door removal pins. Close and open door to check that door closes and opens completely. If door does not close or open completely, you have not pushed hinges completely into frame. Repeat door removal step and reinsert door into hinge slots again.
DCheck operation
10.Turn on power supply. The display panel will light up briefly. “PF” should appear in the temperature display.
11.Check the operation of the cooktop
elements. Push in and turn each surface unit control knob to “HI” position. Check the operation of the cooktop elements and indicator lights.
BAKE BROIL CLEAN
12.Check the operation of the oven
element. Press the “BROIL” pad. “BROIL” will appear in the display. Press the “START” pad. Make sure the oven door is closed and the “ON” light is shown in the display area. After 2 minutes, partially open oven door. You should feel heat from the oven. Press the “CANCEL” pad. If your oven does not heat or an “F”, followed by a number, appears in the display, contact your dealer or check the “If you need service...” section of this Installation Instructions.
Page 3