Whirlpool 3395326 Before you start, Tools and materials needed for installation, Danger

Before you start...

Your safety and the safety of others are				DANGER	Do Not store or operate washer/dryer below
					32°F (some water may remain in washer).
very important.
					Proper operation of dryer cycles requires
We have provided many important safety messages You can be killed or seriously injured if you					temperatures above 45°F. See Use & Care
in this manual and on your appliance. Always read			don’t immediately follow instructions.		Guide for “Winterizing” information.
and obey all safety messages.				WARNING	Check code requirements: Some codes
This is the safety alert symbol.					limit or do not permit installation of clothes
					dryers in garages, closets, mobile homes
This symbol alerts you to potential			You can be killed or seriously injured if you don’t
					and sleeping quarters. (Contact your local
hazards that can kill or hurt you and			follow instructions.		building inspector.)
others.			All safety messages will tell you what the potential		Check utilities: Proper gas, water and
All safety messages will follow the safety alert			hazard is, tell you how to reduce the chance of		electric supply connections must be
symbol and either the word “DANGER” or			injury, and tell you what can happen if the		available.
“WARNING”. These words mean:			instructions are not followed.		Water heater: Set to deliver 140°F water to the
Check location where washer/dryer will				Hot and cold	washer.
be installed. Proper installation is your			gas shutoff	water faucets:	Laundry tub drain system: Needs a 20-gallon
responsibility. The washer/dryer must not			valve	Must be within
					laundry tub. Top of tub must be at least
be installed or stored in an area where it				4 feet of the
					34 inches high and no higher than 72 inches
will be exposed to water and/or				back of the
		rigid	1/8-inch		from floor.
weather. Make sure you have				washer/dryer
		gas	NPT		If a longer drain hose is needed, drain hose
everything necessary for correct				and provide
		supply	plugged
installation.		line	tapping	water pressure	(Part No. 388423) and hose extension kit (Part
Grounded electrical	gas supply line			of 5 -100 PSI.	No. 285442) are available from Whirlpool-
	coupling				authorized parts distributors.
outlet is required. See	38" min. to 41"				Dryer may be exhausted from the rear or
	max.
“Electrical	from floor				left or right side. Exhausting through the
requirements.”
					side requires Part No. 3391335. (See
1/8-inch NPT plugged
					“Exhaust requirements,” Panels B
tapping is required.					and C.)
(See Panel B, Step L.)
This appliance must be attached to					Four-inch metal exhaust
a wall. The cable bracket must be
					vent is required.
secured to a wall stud within a
					SEE RECESSED AREA
27-inch-wide area that is 28 inches
minimum to 41 inches maximum					INSTRUCTIONS ON PANEL G.
from floor. (See Panel F.)
Standpipe drain system: Needs
a two-inch diameter standpipe
with minimum carry-away					Important: Observe all governing
capacity of 17 gallons per					codes and ordinances.
minute. Top of standpipe must				Level floor:
be at least 34 inches high and
no higher than				1-inch maximum slope
72 inches from floor.				under entire washer/dryer.

Floor drain system requires a	Support: Floor must be sturdy enough
siphon break, Part No. 285320,
	to support washer/dryer weight, with
available from a Whirlpool-
	water and clothes, of 500 pounds.
authorized parts distributor.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Failure to do so can result in death, explosion, or fire.

Location: Should be large enough to fully open dryer door to 90°. (See Panel G for “Recessed and closet installation instructions” and “Product dimensions.”)

WARNING: For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death.

—Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

—WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electrical switch; do not use any phone in your building.

•Clear the room, building or area of all occupants.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your

gas supplier, call the fire department.

—Installation and service must be performed by a qualified installer, service agency or the gas supplier.

Tools and materials needed for installation:

utility	Phillips screwdriver
knife	pliers

flat-blade screwdriver

	adjustable
diagonal	wrench (two
cutters	may be
level	required)

A 1" x 4" x 24" board and fasteners are also required (but are not included with this product).

Gas supply requirements

OBSERVE ALL GOVERNING CODES AND ORDINANCES

WARNING

Explosion Hazard

Use a new AGA or CSA approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure gas pressure does not exceed 13" water column. Examples of a qualified person include licensed heating personnel, authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Panel A