Before you start...

Check location where dryer will be installed. Proper installation is your responsibility. The dryer must not be installed or stored in an area where it will be exposed to water and/or weather. Make sure you have everything necessary for correct installation.

Grounded electrical supply is required. See Electrical requirements, Pages 3-4.

Important: Observe all governing codes and ordinances.

Open dryer and remove literature and parts packages.

Support: Floor must be sturdy enough to support dryer weight of 175 pounds (79.4 kg)

Level floor: 1-inch (2.5 cm) maximum slope under entire dryer.

Electrical Shock Hazard

Four-inch metal exhaust duct is required.

Check code requirements: Some codes limit or Do Not permit installation of clothes dryers in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.

Protection from the weather: Proper operation of dryer cycles requires temperatures above 45°F (7.2”C), or the dryer may not shut off when automatic cycles are used.

42-318”

(107.6 cm)

Dryer door clearances

Location must be large enough to fully open dryer door. See Page 10 for recessed and closet requirements.

 

15-318”

(58.4 cm)

(39.1 cm)

 

+

-

r4

large side- swing door

Full-width

Extra-large

I

Mini-hamper

hamper door

hamper

door

door

Page 2

(shown

above)

 

It is the customer’s responsibility:

To contact a qualified electrical installer.

To assure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSVNFPA 70 - latest edition*, and all local codes and ordinances.

Failure to do so could result in death or serious injury.

Fire Hazard

Do Not store gasoline, paint thinners, or other flammable materials near dryer. Fumes from such materials may result in fire or explosion.

Never install dryer up against draperies or curtains or on carpet.

Keep any and all items from falling or collecting behind the dryer.

If you install the dryer in a garage, carport, or areas near vehicles where fumes from gasoline or other flammable materials may be present, the vapors may be heavier than air and remain near floor. Place dryer a minimum of 18 inches (45.7 cm) above floor. Check with your building inspector regarding requirements for this installation.

Failure to follow these instructions could result in a fire or explosion.

Copies of the standards listed above may be obtained from:

*National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

Page 2
Image 2
Whirlpool 3397617 manual Before you start, Important Observe all governing codes and ordinances, Dryer door clearances

3397617 specifications

The Whirlpool 3397617 is a highly regarded dryer heating element known for its efficiency and reliability in enhancing laundry performance. This essential appliance component is specifically designed for various models of Whirlpool dryers, ensuring optimal drying capabilities for a wide range of fabrics and loads.

One of the standout features of the Whirlpool 3397617 is its durable construction. Made from high-quality materials, this heating element is built to withstand the rigors of regular use and deliver consistent performance over time. Its robust design minimizes the risk of burns or malfunctions, thereby providing peace of mind to users.

In terms of specifications, the Whirlpool 3397617 operates at a voltage of 240 volts and a wattage of 5,000 watts. This powerful heating element swiftly generates heat, allowing clothes to dry efficiently without prolonged exposure to heat, which can potentially damage delicate fabrics. The rapid heating ability also contributes to shorter drying cycles, making it a practical choice for households with busy schedules.

Another important characteristic of the Whirlpool 3397617 is its compatibility with a variety of Whirlpool dryer models. This versatility makes it an ideal replacement part, as it can easily be substituted in many different units. This compatibility ensures that users can continue to enjoy the reliability and functionality of their dryers without needing to invest in a whole new appliance.

Incorporating advanced coil technology, the Whirlpool 3397617 provides uniform heat distribution throughout the dryer. This feature significantly enhances drying efficiency, ensuring that every piece of clothing is treated evenly, thereby preventing the risk of over-drying or under-drying.

Installing the Whirlpool 3397617 is straightforward, and most users can complete the replacement with basic tools and minimal time. With its combination of quality, performance, and user-friendliness, this heating element stands out as a top choice for anyone looking to maintain their dryer’s effectiveness and prolong its lifespan.

Overall, the Whirlpool 3397617 is emblematic of Whirlpool’s commitment to producing high-quality home appliances. This heating element not only meets but often exceeds consumer expectations, making it an essential component for efficient laundry care.