Exhaust requirements

WARNING

Fire Hazard Use a heavy metal vent. Do not use a plastic vent. Do not use a metal foil vent.

Failure to follow these instructions can result in death or fire.

Do Not use non-metal flexible vent, or exhaust hoods with magnetic latches.

Do Not exhaust dryer into any gas vent, chimney, furnace, cold air vent, wall, ceiling, concealed space of a building, attic or crawl space, or any other vent used for venting.

Do Not install flexible vent in enclosed walls, ceilings or floors.

Important: Observe all governing codes and ordinances.

Exhaust your dryer to the outside. Moisture and lint indoors may cause:

Lint to gather around the dryer where it can be fuel for a fire.

Moisture damage to woodwork, furniture, paint, wallpaper, carpet, etc.

Housecleaning problems and health problems.

Dura Safe™ venting products are recommended and are available from your dealer.

Four-inch diameter vent must be used.

Use a heavy metal vent. Do Not use plastic or metal foil vent.

Rigid metal vent is recommended to prevent crushing and kinking.

Flexible metal vent must be fully extended and supported when the dryer is in its final position. Remove excess flexible vent to avoid sagging and kinking that may result in reduced air flow.

An exhaust hood should cap the exhaust vent to prevent rodents and insects from entering the home.

Exhaust outlet hood

 

 

 

 

 

must be at least 12

 

 

12"

 

 

inches from the ground

 

 

minimum

or any object that may

 

 

 

 

 

be in the path of the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

exhaust (such as

 

 

 

 

 

flowers, rocks or

 

 

 

 

 

bushes, etc.).

 

 

 

 

 

If using an existing exhaust system, clean lint from entire length of system and make sure exhaust hood is not plugged with lint.

Replace any vinyl or metallized plastic foil vent with rigid metal or flexible metal vent.

Use clamps to seal all joints. Do Not use duct tape, screws or other fastening devices that extend into the interior of the vent to

secure vent.

Service check: Back pressure in any exhaust system used must not exceed

0.6inches in water column measured with an incline manometer at the point that exhaust vent connects to dryer.

Mobile home installation requirements

If codes permit, this dryer is suitable for mobile home installations. The installation of the dryer must conform to the U.S. Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Homes Construction and Safety, Title 24, HUD Part 280) latest edition.

The dryer must be fastened to the floor.

Order Mobile Home Installation Kit, Part No. 346764, from your dealer. Kit includes the necessary fastening hardware and detailed installation instructions. Metal exhaust system is also available through your dealer.

Special provisions must be made for the introduction of outside air into the dryer when installed in a mobile home. The area of any opening for the introduction of outside air (such as a nearby window) should be at least twice as large as the dryer exhaust opening.

 

outside

 

wall

floor

 

enclosed

skirting

area

 

The dryer must be exhausted outside.

The exhaust vent must be securely fastened to a non-combustible portion of the mobile home structure and must not terminate beneath the mobile home.

7

Page 7
Image 7
Whirlpool 8535841 installation instructions Mobile home installation requirements, Dryer must be fastened to the floor

8535841 specifications

The Whirlpool 8535841 is a high-quality replacement refrigerator water filter designed to provide clean and fresh drinking water, ensuring that your household stays hydrated with safe water. This filter is compatible with various Whirlpool refrigerator models, making it a versatile choice for those looking to enhance their refrigerator's water filtration system.

One of the standout features of the Whirlpool 8535841 is its advanced filtration technology. This filter uses activated carbon to effectively reduce contaminants such as chlorine, lead, sediment, and other impurities that can affect the taste and smell of your drinking water. With its ability to significantly improve water quality, the Whirlpool 8535841 ensures that every glass of water is crisp and refreshing.

The filter has a long-lasting performance with a lifespan of up to six months or 200 gallons of water, depending on usage and water quality. This durability means less frequent replacements, which not only saves money but also reduces waste. Installing the filter is a straightforward process, ensuring that homeowners can quickly and easily replace their old filters without the need for professional assistance.

Another noteworthy characteristic of the Whirlpool 8535841 is its ability to maintain optimal water flow. Unlike some lower-quality filters that may restrict water pressure, this filter is designed to provide an uninterrupted supply of clean water. This efficient performance is crucial for families that rely on their refrigerator for ice and chilled water, ensuring that there is always plenty of clean drinking water available.

Moreover, the Whirlpool 8535841 is NSF-certified, meaning it meets strict safety and performance standards. Consumers can have peace of mind knowing that this water filter has undergone rigorous testing to confirm its efficacy in reducing harmful contaminants. The certification serves as a testament to the high quality and reliability of the product, making it a trusted choice for many households.

In summary, the Whirlpool 8535841 water filter offers advanced filtration technology, ease of installation, long-lasting performance, and reliable water flow. With NSF certification to back its effectiveness, this filter is an excellent investment for anyone looking to improve their drinking water quality while enjoying the convenience of a refrigerator-based filtration system. Whether for health concerns or the simple desire for better-tasting water, the Whirlpool 8535841 stands out as a top choice in refrigerator water filtration solutions.