Whirlpool GB2SHKLLS00 Refrigerator Doors, Handle Installation and Removal, Door and Hinge Removal

Models: GB2SHKLLS00

1 36
Download 36 pages 23.81 Kb
Page 7
Image 7
Refrigerator Doors

Refrigerator Doors

Handle Installation and Removal

(Graphics are included later in this section.)

1.Place handle on door as shown.

2.Using a Phillips screwdriver, attach handle to door with handle screws.

3.Place trim pieces on the upper and lower handle ends as shown.

4.Apply firm pressure with your hand on the face of the trim. Slide the top trim down and bottom trim up toward the handle.

5.Using a Phillips screwdriver, attach the freezer handle to the freezer door with the 2 screws provided.

6.To remove handles, reverse directions.

Door and Hinge Removal

Tools Needed: ⁵⁄₁₆-in., ³⁄₈-in., ¹⁄₄ in. hex-head socket wrench, a No. 2 Phillips head and a flat bladed screwdriver.

IMPORTANT:

Before you begin, turn the refrigerator control OFF, unplug refrigerator or disconnect power. Remove food and any adjustable door or utility bins from doors.

All graphics referenced in the following instructions are included later in this section after “Final Steps.”

Cabinet

1.Remove hinge screws from handle side and move them to opposite side (see Graphic 1-1).

2.Remove cabinet hinge hole plugs from cabinet top and move them to opposite side hinge holes as shown (see

Graphic 1-2).

Refrigerator door

1.Remove refrigerator handle assembly as shown. Keep all parts together (see Graphic 2).

2.Remove door handle seal screw front. Move to opposite side of refrigerator door as shown (see Graphic 5).

3.Remove door stop. Move to opposite side of refrigerator door as shown (see Graphic 3).

4.Attach refrigerator handle on opposite side of the refrigerator door with the two screws as shown (see Graphic 2). Replace handle trim as shown.

5.Tighten all screws. Set aside door until hinges and freezer compartment door are in place.

Freezer door

1.Remove freezer handle assembly as shown. Keep all parts together (see Graphic 4).

2.Remove freezer door handle seal screw. Move to opposite side of freezer door.

3.Remove door stop. Move to opposite side of freezer door as shown (see Graphic 3).

4.Attach handle to opposite side of freezer door.

5.Tighten all screws. Set aside door until bottom hinge is installed on product.

⁵⁄₁₆" Hex-Head Top Hinge Screw

1.Unplug refrigerator or disconnect power.

2.Open freezer door and remove bottom hinge cover from the bottom front of the refrigerator.

3.Close the freezer door and keep both doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the hinges are being moved. Do not depend on the door gasket magnets to hold the doors in place while you are working.

4.Remove the parts for the top hinge as shown in Top Hinge graphic. Lift the refrigerator door free from the cabinet.

5.Remove the center hinge pin and remove hinge screws as shown in the Center Hinge graphic. Lift the freezer door free from the cabinet.

6.Remove the parts for the bottom hinge as shown in the Bottom Hinge graphic.

Door Reversal (optional on some models)

IMPORTANT: If you want to reverse your standard doors so they open from the opposite side, follow these steps. If you are not reversing the doors, see “Door and Hinge Replacement.”

Door Stop Screw

Door Handle Seal Screw Front

Flat-Head Handle Screw

Cabinet Hinge Hole Plug

Door and Hinge Replacement

NOTE: Graphic may be reversed if door swing is reversed.

1.Replace the parts for the bottom hinge as shown. Tighten screws. Replace the freezer door.

NOTE: Provide additional support for the doors while the hinges are being moved. Do not depend on the door gasket magnets to hold the doors in place while you are working.

2.Assemble the parts for the center hinge as shown and tighten all screws (see Center Hinge graphic). Replace the refrigerator door.

3.Assemble the parts for the top hinge as shown (see Top Hinge graphic). Do not tighten screws completely.

4.Line up the doors so that the bottom of the refrigerator door aligns evenly with the top of the freezer door. Tighten all screws.

Final Steps

1.Check all holes to make sure that hole plugs and screws are in place. Reinstall top hinge cover (see Top Hinge graphic).

2.Replace the bottom hinge cover.

3.Plug in refrigerator or reconnect power.

4.Reset the controls (see “Using the Controls” section).

5.Return all removable door parts to doors and food to product.

7

Page 7
Image 7
Whirlpool GB2SHKLLS00 manual Refrigerator Doors, Handle Installation and Removal, Door and Hinge Removal, Final Steps