Whirlpool GR2SHWXPQ02 Refrigerator Doors, Complete the Installation, Remove Doors and Hinges

4.Turn shutoff valve ON.

5.Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Style 3

1.Unplug refrigerator or disconnect power.

2.Remove and discard the black nylon plug from the gray water tube on the rear of the refrigerator.

3.Thread the provided nut onto the water valve as shown.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

A

B

Complete the Installation

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

A.Bulb

B.Nut (provided)

4.Turn shutoff valve ON.

5.Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

1.Plug into a grounded 3 prong outlet.

2.Flush the water system. See “Water Dispenser.”

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.

Refrigerator Doors

TOOLS NEEDED: ⁵⁄₁₆" hex-head socket wrench, #2 Phillips screwdriver, flat-blade screwdriver, ⁵⁄₁₆" open-end wrench, flat 2" putty knife.

IMPORTANT:

■Unplug refrigerator or disconnect power.

■Turn off the water supply to the refrigerator. If there is water in the dispenser’s water line, some spilling may occur during door swing reversal.

■Remove food and any adjustable door or utility bins from doors.

■If you only want to remove and replace the doors, see “Remove Doors and Hinges” and “Replace Doors and Hinges.”

■All graphics referenced in the following instructions are included later in this section after “Final Steps.”

5.Pull the water dispenser wire/tube assembly out of the channel on the bottom of the refrigerator door. See Graphic 2.

6.Disconnect the wiring plug. See Graphic 3.

7.Disconnect the water dispenser tubing. Press the red outer ring against the face of the fitting and pull the dispenser tubing free. See Graphic 10.

NOTE: There may be water in the dispenser tubing if the dispenser has been used.

8.Remove the parts for the top hinge. See Graphic 4. Lift the freezer door free from the cabinet.

9.Remove the ⁵⁄₁₆" hex-head screw from the center rail. Loosen the two screws on the side just enough to remove the center hinge. Remove the center hinge. Replace the center rail screw. See Graphic 5.

10.Lift the refrigerator door free from the cabinet.

11.Remove the parts for the bottom hinge. See Graphic 6.

Remove Doors and Hinges

⁵⁄₁₆" Hex-head hinge screw

1.Unplug refrigerator or disconnect power.

2.Turn off the water supply to the refrigerator.

3.Open the refrigerator door and remove the base grille from the bottom front of the refrigerator. See Graphic 1.

4.Close the refrigerator door and keep both doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.

Reverse Doors (optional)

IMPORTANT:

■If you want to reverse your doors so that they open in the opposite direction, follow these steps. If you are not reversing the doors, see “Replace Doors and Hinges.”

■The the graphics shown are for a right-hand swing refrigerator (hinges factory installed on the right).

Round-Head	Door Handle
Handle Screw	Screw Hole Plug

5