Whirlpool RUD4000 Canceling a Cycle, Changing a Cycle or Setting, Adding Items During a Cycle

Models: RUD4000

1 32
Download 32 pages 41.63 Kb
Page 11
Image 11
Use this cycle for rinsing

 

 

 

 

Use this cycle for rinsing

Do not use

 

 

 

 

 

 

 

RINSE

 

dishes, glasses, and

 

detergent

 

 

 

silverware that will not be

with this

 

 

& HOLD

 

 

 

 

washed right away.

 

cycle.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Wash

Rinse

 

Rinse

Main

Rinse

Final

Dry

Time

Water

 

 

 

 

 

 

Wash

 

Rinse

 

(min)

Usage

 

 

 

 

 

 

 

 

 

 

 

(gal/L)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

20

2.9/10.9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Canceling a Cycle

You can cancel a cycle at any time.

1.Turn the cycle control knob slowly clockwise until you hear water draining. Let the dishwasher drain completely.

2.Open the door.

3.Turn the cycle control knob to Off.

Changing a Cycle or Setting

You can change a cycle anytime during a cycle.

1.Lift the door latch to stop the cycle.

2.Turn the cycle control knob clockwise.

3.Check the detergent dispensers. They must be filled properly for the new cycle.

NOTE: Turning the cycle control knob can cause the covered detergent dispenser section to open and release the detergent. Check the covered section if the cycle uses detergent in both sections.

4.Close the door firmly until it latches. The dishwasher starts a new cycle.

Adding Items During a Cycle

You can add an item anytime before the main wash starts, or the cycle control knob reaches Normal Wash.

1.Lift up the door latch to stop the cycle. Wait for the spraying action to stop before opening the door.

2.Open the door and add the item.

3.Close the door, but do not latch it. Wait 30 seconds for the air in the dishwasher to warm up. This reduces the amount of moisture escaping from the vent when restarting a cycle.

4.Close the door firmly until it latches. The dishwasher resumes the cycle.

Option Selections

You can change an option anytime before the selected option begins. For example, you can press an unheated drying option any time before drying begins.

Energy Saver Dry

Select this option to dry dishes without heat and save energy. The dishes take longer to dry and some spotting can occur.

For best drying, use a liquid rinse aid. Some items (such as plastics) may need towel drying.

NOTE: Energy Saver Dry is an option with all cycles except Rinse & Hold.

Heated Dry

Select this option to dry dishes with heated air. For best drying results, use a liquid rinse aid and heated drying.

NOTE: Heated Dry is an option with all cycles except Rinse & Hold.

Plate Warmer (on some models)

Use the Plate Warmer cycle to warm serving dishes or dinner plates.

NOTE: Use the heated drying option with the Plate Warmer.

1.Close and latch the door.

2.Turn the cycle control knob to Plate Warmer.

3.Allow 8 minutes for the cycle to heat the dishware.

4.Press HEAT DRY.

Drying System

During drying, you can see steam escaping through the vent at the upper left corner of the door. This is normal as the heat dries your dishes.

IMPORTANT: The vapor is hot. Do not touch the vent during drying.

11

Page 11
Image 11
Whirlpool RUD4000 Canceling a Cycle, Changing a Cycle or Setting, Adding Items During a Cycle, Option Selections, cycle