INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Tools needed

Tape measure

Marker or pencil

Screwdriver

Pipe-joint compound

¹⁵⁄₁₆" combination wrench

 

resistant to LP gas

Noncorrosive leak-detection

Pipe wrench

 

solution

 

 

 

Wrench or pliers

Parts supplied

Gas pressure regulator

Burner grates

Burner caps

Clamping brackets (2)

2¹⁄₂" (6.4 cm) clamping screws (2)

Parts needed

Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See “Electrical Requirements” and “Gas Supply Requirements” sections.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the underside of the cooktop base.

A

To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

The cooktop should be installed in a location away from strong draft areas, such as windows, doors and strong heating vents or fans.

All openings in the wall or floor where cooktop is to be installed must be sealed.

Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

Grounded electrical supply is required. See “Electrical Requirements” section. Proper gas supply connection must be available. See “Gas Supply Requirements” section.

The cooktop is designed to hang from the countertop by its side or rear flanges.

The gas and electric supply should be located as shown in “Cabinet Dimensions” section so that they are accessible without requiring removal of the cooktop.

Provide cutout in right rear corner of cutout enclosure as shown to provide clearance for gas inlet, power supply cord, and to allow the rating label to be visible.

IMPORTANT: To avoid damage, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage.

Mobile Home - Additional Installation Requirements

The installation of this cooktop must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.

In Canada, the installation of this cooktop must conform with the current standards CAN/CSA-A240-latest edition, or with local codes.

A. Model/serial rating plate

3

Page 3
Image 3
Whirlpool W10131955C installation instructions Installation Requirements, Tools and Parts, Location Requirements

W10131955C specifications

The Whirlpool W10131955C is a high-performance refrigerator water filter designed to improve the quality of drinking water and ice produced by Whirlpool refrigerators. This filter is known for its innovative features and reliable technology, ensuring that users enjoy fresh, clean water.

One of the standout characteristics of the W10131955C is its advanced filtration system. It utilizes a combination of activated carbon and other filtration materials to effectively reduce contaminants such as chlorine, lead, and other harmful impurities that can affect water taste and quality. This not only enhances the flavor of the water but also provides peace of mind for households concerned about water safety.

The installation process of the W10131955C is user-friendly, allowing homeowners to replace the filter without the need for any special tools. This tool-free installation is a significant advantage, making it accessible for anyone, regardless of their DIY experience. The filter typically requires replacement every six months or after filtering approximately 200 gallons of water, which helps maintain optimal performance and water quality.

In addition to its filtration capabilities, the W10131955C is designed with compatibility in mind. It is specifically designed for use in several Whirlpool, Maytag, KitchenAid, and Jenn-Air refrigerator models. This ensures that a wide range of users can benefit from its advanced filtration technology, making it a versatile choice for families with different appliances.

The W10131955C filter also features an NSF certification, which indicates that it meets strict safety and performance standards. This certification provides additional assurance to consumers about the filter's effectiveness and reliability.

Moreover, the filter's compact design allows for easy storage and reduces waste, contributing to environmentally-friendly practices. By using the W10131955C, households can minimize bottled water usage, thus reducing plastic waste and promoting sustainability.

Overall, the Whirlpool W10131955C is a top-tier water filter that combines advanced technology with user-friendly features. Its efficient filtration system, easy installation, and compatibility with various refrigerator models make it an essential component for anyone looking to ensure that their drinking water is safe, clean, and delicious.