Whirlpool W10203462D Electronic Oven Control, Display, Oven Indicator Lights, Start, Cancel/Off

Models: W10203462D

1 16
Download 16 pages 23.71 Kb
Page 8
Image 8
ELECTRONIC OVEN CONTROL

ELECTRONIC OVEN CONTROL

A BCD E

I

H

G

F

A. Oven light

 

F. Temp/hour

 

B. Clock

 

G. Broil

 

C. Display

 

H. Bake

 

D. Start (control lock)

 

I. Timer

 

E. Cancel/off

 

 

 

Display

When power is first supplied to the appliance, a flashing time will appear on the display. Press CANCEL/OFF to clear flashing time from the display.

If flashing time appears, a power failure has occurred. Press CANCEL/OFF and reset the Clock if needed.

When the oven is not in use, the display shows the time of day.

When performing a cook or timer function, the display will show either hours and minutes, or minutes and seconds.

Oven Indicator Lights

The indicator lights are located on both sides of the display. The indicator lights light up or flash when the oven is in one of the following modes: Bake, Broil or Timer.

Start

The Start pad begins any oven function. If the Start pad is not pressed within 5 seconds after pressing a function pad, the Push to Start (“PSH”) indicator light will flash and the push to start tone will sound as a reminder.

If the Start pad is not pressed within 1 minute after pressing a function pad, the oven display will return to the time of day mode and the programmed function will be canceled.

Cancel/Off

The Cancel/Off pad stops any function except the Clock, Timer and Control Lock.

Clock

This is a 12-hour clock and does not show a.m. or p.m.

To Set:

Before setting, make sure the oven and Timer are off.

1.Press CLOCK.

2.Press the TEMP/HOUR “up” or “down” arrow pads to set the time of day.

3.Press CLOCK or START.

Tones

Tones are audible signals, indicating the following:

One tone

Valid pad press

Oven is preheated (long tone)

Function has been entered

Three tones

Invalid pad press

Push to start reminder

Cycling tones

End of cycle

Fahrenheit and Celsius

The temperature is preset at Fahrenheit, but can be changed to Celsius.

To Change: Press and hold BROIL for 5 seconds. A tone will sound, and “C” will appear on the display. Repeat to change back to Fahrenheit. To exit mode, press CANCEL/OFF.

Timer

The timer can be set in hours or minutes up to 12 hours and

59 minutes, and counts down the set time either in hours and minutes, or in minutes and seconds. The timer does not start or stop the oven.

To Set:

1.Press TIMER. The timer indicator light will light up. If no action is taken after 1 minute, the display will return to the time of day, bake or broil mode.

2.Press the TEMP/HOUR “up” or “down” arrow pads to set the length of time.

3.Press START. When the set time ends, end-of-cycle tones will sound.

4.Press TIMER pad twice anytime to cancel the timer and reminder tones.

If the Cancel/Off pad is pressed the oven will turn off and the cook function will be disabled.

To display the time of day for 5 seconds when the timer is counting down, press the CLOCK pad.

If the Start pad is not pressed within 5 seconds after pressing the Timer pad or Temp/Hour arrow pads, the “PSH” indicator light will flash and the push to start tone will sound as a reminder.

The timer can be reprogrammed to change the time while it is running.

To Reprogram:

1.Press TIMER.

2.Press TEMP/HOUR “up” or “down” arrow pads to adjust time.

3.Press START.

8

Page 8
Image 8
Whirlpool W10203462D manual Electronic Oven Control, Display, Oven Indicator Lights, Start, Cancel/Off, Clock, Tones, Timer