Whirlpool W10282149B manual Vacationand Moving Care, To shut down the ice maker

Models: W10282149B

1 28
Download 28 pages 32.59 Kb
Page 11
Image 11

9.Remove, clean and replace the ice scoop and ice scoop holder.

After removing the ice scoop, remove the holder by removing the two thumb screws.

Wash the ice scoop holder along with the other interior components using the following instructions.

Replace the ice scoop holder by replacing the thumb screws.

A

B

A. Thumb screws

B. Ice scoop holder

10.Wash the interior components (cutter grid, exterior of hoses, and water pan) and the storage bin, door gasket, ice scoop, and ice scoop holder with mild soap or detergent and warm water. Rinse in clean water. Then clean the same parts with a solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L) warm water. Rinse again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts in dishwasher. They cannot withstand temperatures above 145°F (63°C).

11.Replace water pan by pushing back on the bottom with one hand while pushing up and back on the top. Secure the water pan by replacing both screws.

12.Check the following:

Drain cap from the water pan is securely in place. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

Hose from water pan is inserted into storage bin drain opening.

13.Slide the cutter grid back into place and secure it by replacing the right-hand screw and plastic spacer. Then tighten the left- hand screw. Reconnect the cutter grid harness and the ice level sensor harness.

14.Replace the plastic cutter grid cover and the two screws.

15.Gently wipe the control panel with a soft, clean dishcloth using warm water and a mild liquid dish detergent.

16.Plug in ice maker or reconnect power.

17.After cleaning, make sure that all controls are set properly and that no control indicators are flashing.

Vacationand Moving Care

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

To shut down the ice maker:

1.Unplug ice maker or disconnect power.

2.Remove all ice from storage bin.

3.Shut off the water supply.

4.Remove the two screws in the lower access panel and the two screws from the base grille area of the front panel support. Pull forward to remove the lower access panel.

5.Disconnect the inlet and outlet lines to water valve. Allow these lines to drain and then reconnect to the valve.

6.Replace lower access panel and screws.

7.Drain water from water pan by removing the drain cap.

8.If the room temperature will drop below 32°F (0°C), water must be removed from the drain line.

For ice makers with a drain pump installed:

Plug in ice maker or reconnect power.

Turn ice maker off and remove all remaining ice from ice bin.

Pour 1 qt (0.95 L) of water into the ice bin near the drain and let the ice maker stand for approximately 5 minutes. This will allow the water in the bin to drain into the drain pump so that the pump will remove the remaining water from the ice bin and the drain pump.

Unplug ice maker or disconnect power.

9.Before using again, clean the ice maker and storage bin.

10.Plug into a grounded 3 prong outlet.

NOTE: All components of the ice maker are permanently lubricated at the factory. They should not require any additional oiling throughout the normal life of the machine.

11

Page 11
Image 11
Whirlpool W10282149B manual Vacationand Moving Care, To shut down the ice maker, For ice makers with a drain pump installed

W10282149B specifications

The Whirlpool W10282149B is a cutting-edge refrigerator designed to enhance convenience and efficiency in your kitchen. It combines advanced technology with a sleek design, making it a popular choice for modern households. This refrigerator stands out with its ample storage capacity, allowing families to store fresh food and beverages without worrying about running out of space.

One of the main features of the Whirlpool W10282149B is its Adaptive Defrost technology. This innovative feature adjusts the defrosting cycle based on the refrigerator's usage patterns. By optimizing the defrost schedule, it helps maintain ideal temperatures while reducing energy consumption. This not only contributes to a more energy-efficient appliance but also ensures that your food stays fresher for longer.

Another remarkable aspect of the W10282149B is its Accu-Chill temperature management system. This system uses built-in sensors to monitor the internal temperature and adjust cooling accordingly. As a result, it quickly reaches the desired temperature after loading groceries and maintains a consistent environment for optimal food preservation. This technology is particularly beneficial in preventing spoilage and extending the shelf life of perishable items.

The refrigerator boasts a sleek, finger-resistant stainless steel exterior, which adds a modern touch to any kitchen. Additionally, it features adjustable shelves and humidity-controlled crisper drawers, providing flexibility for organizing your groceries. The design allows you to customize the interior layout according to your storage needs, making it easier to access your favorite foods.

Energy efficiency is a priority for Whirlpool, and the W10282149B is no exception. It is ENERGY STAR certified, which means it meets strict energy efficiency guidelines. This certification translates into cost savings on your energy bill and a reduced carbon footprint.

Furthermore, the W10282149B includes a factory-installed ice maker, ensuring a steady supply of ice for your drinks. This feature eliminates the need for manual ice trays, adding a level of convenience to your daily routine.

In conclusion, the Whirlpool W10282149B refrigerator is a versatile appliance that combines advanced technologies with user-friendly features. Its adaptive defrost, Accu-Chill temperature management system, and customizable storage options make it an ideal choice for families seeking efficiency and reliability in their kitchen.