Planning the installation | Patton electronic 4110, 4520 specs

SmartNode 4520 & 4110 Series User Manual	3 • Hardware installation

Planning the installation

Before you start the actual installation, it is strongly recommended that you gather all the information needed to install and setup the device. See table 4 for an example of what pre-installment checks you might need to carry out. Having carried out the pre-installation checks enables you to install and set up your gateway router into an existing infrastructure with confidence.

The mains outlet that is utilized to power the equipment must be within 1 foot (3 meters) of the device and shall be easily accessible.

CAUTION

Note When setting up your gateway router consider cable length limitations, and potential electromagnetic interference (EMI) as defined by the applicable local and international regulations. Ensure that your site is properly prepared before beginning installation.

Before installing the gateway router device, the following tasks should be completed:

•Create a network diagram (see section “Network information” on page 30)

•Gather IP related information (see section “IP related information” on page 30 for more information)

•Install the hardware and software needed to configure the SmartNode. (See section “Software tools” on page 30)

•Verify power source reliability (see section “Power source” on page 30).

When you finish preparing for gateway router installation, go to section “Installing the gateway router” on page 31 to install the device.

Planning the installation

28

Image 28

Patton electronic 4110, 4520 Planning the installation, Create a network diagram see section Network information on

Contents

SmartNode 4520 & 4110 Series Mailsupport@patton.com Table of Contents LEDs status and monitoring Cabling Audience About this guideStructure Precautions Safety when working with electricity Preventing electrostatic discharge damage General observations Typographical conventions used in this documentGeneral conventions Chapter contents General information SmartNode Series VoIP routers overview SmartNode Router SmartNode 4524 shown SmartNode 4520 Series router Examples of SN4520 Series rear panels SmartNode 4520 Series power input connectors Ports descriptions SmartNode 4520 Series front panels SmartNode 4110 Series router Examples of SN4110 Series rear panels SmartNode 4110 Series power input connectors Port. EuroPOTS support Etsi EG201 SmartNode 4110 Series front panels Applications overview Applications for SmartNode 4110 Series IntroductionSIP and H.323 terminal and Pstn gateways Application-ITSP dial-in access Application-Analog line extension over IP Application-Private line automatic ringdown Plar Application-Enterprise campus BRI to FXS telephony extension Applications for SmartNode 4520 Series Application-PBX toll bypass gateway Application-SOHO off-premise extension Home office networking Application-Single-phone Pstn and VoIP access Single-phone access Hardware installation Planning the installation Create a network diagram see section Network information on Installation checklist Task Verified by Date Power source Site logNetwork information IP related information Installing the gateway router Connecting cablesLocation and mounting requirements Mounting the gateway router Analog FXS connection Pin Signal Installing the Ethernet cable Hardware installation Connecting to external power source Hardware installation Getting started with the SmartNode Steps for setting up a new SmartNode Power connection and default configuration Configure IP addressConnect with the serial interface Login Changing the IP address Load configuration Connect the SmartNode to the network Bootloader Start Bootloader Start-up with factory configuration Load a new application image SmartWare via Tftp Copy tftp//tftpserveraddress/server path/b1 flash Additional information Load a new application image SmartWare via the serial link LEDs status and monitoring Status LEDs Examples of SN4520 Series front panels Examples of SN4110 Series front panels LED Contacting Patton for assistance Warranty coverage Contact information Return for credit policy RMA numbers Appendix a Compliance CE Declaration of Conformity ComplianceAuthorized European Representative FCC Part 68 Acta Statement FXO Ports Radio and TV Interference FCC PartIndustry Canada Notice FXO Ports Industry Canada Notice FXO Ports Appendix B Specifications Voice processing signalling dependent Voice connectivityConnectivity Fax and modem support IP services Voice signallingVoice routing-session router Dimensions Weight and power dissipationManagement Operating environment Identification of the SmartNode devices via Snmp Power supplyAC version Identification of the SmartNode devices via Snmp Appendix C Cabling Connecting a serial terminal Serial console Ethernet 10Base-T and 100Base-T Ethernet cross-over Ethernet straight-through Connecting an FXS device Analog FXS Connecting to an FXO line socket Analog FXO Appendix D Port pin-outs Console port Ethernet 10Base-T and 100Base-T port FXS port FXO port Appendix E SmartNode 4110 Series factory configuration SmartNode 4110 Series factory configuration Appendix F SmartNode 4520 Series factory configuration SmartNode 4520 Series factory configuration Appendix G Installation checklist Installation checklist