Patton electronic 4520, 4110 manual

SmartNode 4520 & 4110 Series User Manual4 • Getting started with the SmartNode

Step	Command	Purpose

8	RedBoot> go	Starts the application image that was down-
		loaded into the volatile memory (RAM).

Note With the Bootloader, only the Ethernet interface 0/0 is available. The Boot- loader applies the IP address, subnet mask, and default gateway that were last configured by the Bootloader itself or by another application (e.g. Smart- Ware). If an application configured the Ethernet interface 0/0 to use DHCP, the Bootloader will also use DHCP to learn the interface configuration. It can receive and apply the IP address, subnet mask, default gateway, and default (TFTP) server (transmitted as basic DHCP information ‘Next server IP address’).

Note This procedure does not download the respective CLI description file.

Download it after starting up SmartWare with the following command:

copy tftp://<tftp_server_address>/<server path>/b1 flash:

Example: Downloading and storing a new application image (SmartWare)

RedBoot> ip	-l	172.16.40.98/19
RedBoot> ip	-g	172.16.32.1
RedBoot> ping -h			172.16.32.100
Network PING -		from 172.16.40.98 to 172.16.32.100
..........PING		-	received 10 of 10 expected

RedBoot> load -r -v -h 172.16.32.100 -b 0x1800100 /Sn4xxx/image.bin Using default protocol (TFTP)

-

Raw file loaded 0x01800100-0x0199ca6b, 1689964 bytes, assumed entry at 0x01800100

RedBoot> fis delete -n 1

Delete image 1 - continue (y/n)? y

... Erase from 0x60030000-0x601cc974: ..........................

RedBoot> fis create

Use address 0x01800100, size 1684402 ? - continue (y/n)? y

... Erase from 0x60030000-0x601cb3ba: ..........................

... Program from 0x00011eec-0x00011ef4 at 0x60030000: .

... Program from 0x01800100-0x0199b4b2 at 0x60030008: ..........................

... Program from 0x00011eec-0x00011ef4 at 0x60030000: . Image successfully written to flash

RedBoot>	fis list -l
Id Address		Length	State	Description
Entry		Load Addr		Version

--------------------------------------------------------------------

1 0x60030000		1693438	valid	SmartWare R2.10 BUILD28015
0x01800100		0x01800100		V2.10
RedBoot>	go
Starting	'SmartWare R2.10		BUILD28015' at 0x01800100 via 0x01800100

Bootloader

45

Image 45

Patton electronic 4520, 4110 user manual Copy tftp//tftpserveraddress/server path/b1 flash

Contents

SmartNode 4520 & 4110 Series Mailsupport@patton.com Table of Contents LEDs status and monitoring Cabling About this guide AudienceStructure Safety when working with electricity Precautions Preventing electrostatic discharge damage Typographical conventions used in this document General observationsGeneral conventions General information Chapter contents SmartNode Router SmartNode 4524 shown SmartNode Series VoIP routers overview Examples of SN4520 Series rear panels SmartNode 4520 Series router SmartNode 4520 Series power input connectors Ports descriptions SmartNode 4520 Series front panels Examples of SN4110 Series rear panels SmartNode 4110 Series router SmartNode 4110 Series power input connectors Port. EuroPOTS support Etsi EG201 SmartNode 4110 Series front panels Applications overview Introduction Applications for SmartNode 4110 SeriesSIP and H.323 terminal and Pstn gateways Application-Analog line extension over IP Application-ITSP dial-in access Application-Enterprise campus BRI to FXS telephony extension Application-Private line automatic ringdown Plar Application-PBX toll bypass gateway Applications for SmartNode 4520 Series Home office networking Application-SOHO off-premise extension Single-phone access Application-Single-phone Pstn and VoIP access Hardware installation Create a network diagram see section Network information on Planning the installation Task Verified by Date Installation checklist Site log Power sourceNetwork information IP related information Connecting cables Installing the gateway routerLocation and mounting requirements Mounting the gateway router Analog FXS connection Pin Signal Installing the Ethernet cable Hardware installation Connecting to external power source Hardware installation Getting started with the SmartNode Steps for setting up a new SmartNode Configure IP address Power connection and default configurationConnect with the serial interface Changing the IP address Login Connect the SmartNode to the network Load configuration Start Bootloader Bootloader Load a new application image SmartWare via Tftp Start-up with factory configuration Copy tftp//tftpserveraddress/server path/b1 flash Load a new application image SmartWare via the serial link Additional information LEDs status and monitoring Examples of SN4520 Series front panels Status LEDs Examples of SN4110 Series front panels LED Contacting Patton for assistance Contact information Warranty coverage RMA numbers Return for credit policy Appendix a Compliance Compliance CE Declaration of ConformityAuthorized European Representative Radio and TV Interference FCC Part FCC Part 68 Acta Statement FXO PortsIndustry Canada Notice FXO Ports Industry Canada Notice FXO Ports Appendix B Specifications Voice connectivity Voice processing signalling dependentConnectivity Fax and modem support Voice signalling IP servicesVoice routing-session router Weight and power dissipation DimensionsManagement Operating environment Power supply Identification of the SmartNode devices via SnmpAC version Identification of the SmartNode devices via Snmp Appendix C Cabling Serial console Connecting a serial terminal Ethernet cross-over Ethernet 10Base-T and 100Base-T Ethernet straight-through Analog FXS Connecting an FXS device Analog FXO Connecting to an FXO line socket Appendix D Port pin-outs Ethernet 10Base-T and 100Base-T port Console port FXO port FXS port Appendix E SmartNode 4110 Series factory configuration SmartNode 4110 Series factory configuration Appendix F SmartNode 4520 Series factory configuration SmartNode 4520 Series factory configuration Appendix G Installation checklist Installation checklist