Port. EuroPOTS support Etsi EG201 | Patton electronic 4110, 4520

SmartNode 4520 & 4110 Series User Manual	1 • General information

Ports descriptions

The SmartNode 4110 Series rear panel ports are described in table 3.

		Table 3. Rear panel ports

Port	Location	Description

10/100 Ethernet	Rear panel	RJ-45 connector (see figure 5 on page 16) that connects the router to an
ETH 0/0		Ethernet device (a cable or DSL modem, LAN hub or switch, for example).
Analog voice port,	Rear panel	FXS RJ-11(6 position, 4 wire) connectors (see figure 16 on page 32) that
FXS		connect the router with an analog terminal (a telephone, for example) FXO
		port. EuroPOTS support (ETSI EG201 188).

Analog voice port,	Rear panel	FXO RJ-11(6 position, 4 wire) connectors (see figure 16 on page 32) that
FXO		connect the router with an analog line (FXS port). EuroPOTS support (ETSI
		EG201 188).
Power	Rear panel	The gateway is available in a DC or AC power input version (see
		figure 6), labeled as follows:
		• AC version (Internal power supply): 100–240 VAC, 50/60 Hz, 200 mA
		• DC version: 12 VDC, 1.25 A

Console	Front panel	Used for service and maintenance, the Console port (see figure 7 on page 19),
		an RS-232 RJ-45 connector, connects the router to a serial terminal such as a PC
		or ASCII terminal (also called a dumb terminal).

Reset button behavior

For those SmartNode devices that have a Reset button on the rear panel, its behavior is as follows:

•To restart the unit with the current startup configuration—Press for less than 1 second and release the Reset button. The SmartNode will restart with the current startup configuration.

•To restart the unit with factory default configuration—Press the Reset button for 5 seconds until the Power LED starts blinking. The unit will restart with factory default configuration.

•To restart the unit in bootloader mode (to be used only by trained SmartNode technicians)—Start with the unit powered off. Press and hold the Reset button while applying power to the unit. Release the Reset button when the Power LED starts blinking so the unit will enter bootloader mode.

SmartNode Series VoIP routers overview

18

Image 18

Patton electronic 4110, 4520 user manual Port. EuroPOTS support Etsi EG201

Contents

SmartNode 4520 & 4110 Series Mailsupport@patton.com Table of Contents LEDs status and monitoring Cabling About this guide AudienceStructure Precautions Safety when working with electricity Preventing electrostatic discharge damage Typographical conventions used in this document General observationsGeneral conventions Chapter contents General information SmartNode Series VoIP routers overview SmartNode Router SmartNode 4524 shown SmartNode 4520 Series router Examples of SN4520 Series rear panels SmartNode 4520 Series power input connectors Ports descriptions SmartNode 4520 Series front panels SmartNode 4110 Series router Examples of SN4110 Series rear panels SmartNode 4110 Series power input connectors Port. EuroPOTS support Etsi EG201 SmartNode 4110 Series front panels Applications overview Introduction Applications for SmartNode 4110 SeriesSIP and H.323 terminal and Pstn gateways Application-ITSP dial-in access Application-Analog line extension over IP Application-Private line automatic ringdown Plar Application-Enterprise campus BRI to FXS telephony extension Applications for SmartNode 4520 Series Application-PBX toll bypass gateway Application-SOHO off-premise extension Home office networking Application-Single-phone Pstn and VoIP access Single-phone access Hardware installation Planning the installation Create a network diagram see section Network information on Installation checklist Task Verified by Date Network information Power sourceSite log IP related information Location and mounting requirements Installing the gateway routerConnecting cables Mounting the gateway router Analog FXS connection Pin Signal Installing the Ethernet cable Hardware installation Connecting to external power source Hardware installation Getting started with the SmartNode Steps for setting up a new SmartNode Configure IP address Power connection and default configurationConnect with the serial interface Login Changing the IP address Load configuration Connect the SmartNode to the network Bootloader Start Bootloader Start-up with factory configuration Load a new application image SmartWare via Tftp Copy tftp//tftpserveraddress/server path/b1 flash Additional information Load a new application image SmartWare via the serial link LEDs status and monitoring Status LEDs Examples of SN4520 Series front panels Examples of SN4110 Series front panels LED Contacting Patton for assistance Warranty coverage Contact information Return for credit policy RMA numbers Appendix a Compliance Compliance CE Declaration of ConformityAuthorized European Representative Radio and TV Interference FCC Part FCC Part 68 Acta Statement FXO PortsIndustry Canada Notice FXO Ports Industry Canada Notice FXO Ports Appendix B Specifications Connectivity Voice processing signalling dependentVoice connectivity Fax and modem support Voice signalling IP servicesVoice routing-session router Management DimensionsWeight and power dissipation Operating environment Power supply Identification of the SmartNode devices via SnmpAC version Identification of the SmartNode devices via Snmp Appendix C Cabling Connecting a serial terminal Serial console Ethernet 10Base-T and 100Base-T Ethernet cross-over Ethernet straight-through Connecting an FXS device Analog FXS Connecting to an FXO line socket Analog FXO Appendix D Port pin-outs Console port Ethernet 10Base-T and 100Base-T port FXS port FXO port Appendix E SmartNode 4110 Series factory configuration SmartNode 4110 Series factory configuration Appendix F SmartNode 4520 Series factory configuration SmartNode 4520 Series factory configuration Appendix G Installation checklist Installation checklist