![INSTALLATION](/images/new-backgrounds/22142/221425x1.webp)
On some units, the Outdoor Ambient Temperature (OAT) and Outdoor Coil Temperature (OCT) sensors may be attached permanently to the controller. The
Before removing the old controller, note the location of the OCT sensor on the outdoor coil. The new sensor should be attached to the coil in the same location, or as close as possible. The OAT sensor is typically
Four metal standoffs are used to support and mount the control into the unit.
Board size is 3.375 in. x 3.625 in. and requires 1 inch of headroom (not including mounting).
Typical System Wiring Table
47D40 |
|
|
Terminal | Type | System Component Connection |
C | 0.25” QC | Reversing valve common |
RV | 0.25” QC | Reversing valve output |
CC | 0.25” QC | Compressor contactor coil |
Yout | 0.25” QC | Compressor call output |
C (2) | 0.25” QC | Common, 24VAC return |
D | 0.25” QC | Defrost output |
Y | 0.25” QC | Compressor call input |
B | 0.25” QC | Heating mode signal input |
R (2) | 0.25” QC | 24VAC input |
Fan (2) | 0.25” QC | Outdoor fan control |
OAT | Outdoor ambient temperature sensor | |
OCT | Outdoor coil temperature sensor |
INSTALLATION
NOTE
All wiring should be installed according to local and national electrical codes and ordinances.
The
The control must be secured to an area that will experience a minimum of vibration and remain below the maximum ambient temperature rating of 150o F. The control is approved for minimum ambient temperatures of
Any orientation is acceptable.
Refer to the wiring diagram and wiring table when connecting the
UL approved, 105o C rated 18 gauge min., stranded 2/64” thick insulation wire is recommended for all low voltage safety circuit connections.
UL approved, 105o C rated 16 gauge min., stranded 2/64” thick insulation wire is recommended for all line voltage connections.
Following installation or replacement, follow appliance manufacturer’s recommended installation or service instructions to insure proper operation.
|
|
|
|
|
|
|
| C |
|
|
|
COMPRESSOR | R |
| S |
| HERM | FAN | S | R | OUTDOOR | ||
|
|
| C |
|
|
|
|
|
| C | FAN MOTOR |
|
|
|
|
|
|
| RUN CAPACITOR |
|
|
| |
CC |
|
|
|
|
|
|
|
|
|
|
|
COMPRESSOR |
|
|
|
| TO THERMOSTAT |
|
|
|
| ||
CONTACTOR |
|
|
|
|
|
|
|
| |||
| L1 |
| L2 |
|
|
|
|
|
|
| |
|
|
|
| D | Y | C | B | R |
|
|
|
|
|
|
|
|
|
|
| FAN |
|
|
|
|
|
| Yout |
|
|
|
|
|
|
| |
|
|
| CC |
|
|
| FAN |
|
|
| |
|
|
|
|
|
|
|
|
|
| ||
|
|
| RV |
|
|
| OAT |
|
|
| |
REVERSING |
|
|
|
|
|
|
|
|
|
| |
RV |
|
| C |
|
|
|
|
|
|
| |
VALVE |
|
|
|
|
|
|
| OCT |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Legend |
|
|
|
|
|
|
|
|
|
|
|
Low Voltage |
| |
Line Voltage | Demand Defrost Control | |
Internal Control | ||
| ||
Tracing |
|
Fig 1. Typical System Wiring Diagram
3