IMPORTANT: Clean out the screen, within the brewcone, to maintain
the flow of brewed tea. Neglecting this screen will eventually cause the brewcone to overflow, spilling hot liquid over the unit.
CAUTION: DO NOT use undiluted bleach or chlorine.
CLEANING
Regular cleaning of the Iced Tea Brewer and tea container is essential in maintaining the highest quality iced tea your equipment is capable of producing.
1.Wipe any spills, dust or debris from the exterior surfaces with a damp cloth. The outside surfaces of the brewer should be cleaned with stainless steel polish only, to prevent scratches.
2.Clean the sprayhead and domed area around the sprayhead with a detergent solution and scrub well to remove residue. Rinse with and clear water. Dry with clean cloth.
3.Remove the wire filter holder from the brew basket and wash both parts with a detergent solution or put these parts through a dishwasher.
4.Wash the tea container and top cover with a detergent solution. Remove the faucet assembly. Unscrew the handle assembly shank. Using the same brush clean the faucet body inlet and outlet. Clean the faucet cap and silicone seat cup.
5.After the cleaning, place the parts (sprayhead, brewcone and basket and faucet parts) into a sink to be sanitized. To sanitize the disassembled parts:
A.Use a clean container to submerge all parts. Wear rubber gloves for protection.
B.Immerse in commerical Bar
6.Thoroughly rinse parts with hot water. Air dry, all parts that were sanitized.
7.After cleaning, sanitizing and drying, assemble any parts taken from the brewer and tea container.
WARNING DO NOT refrigerate unused tea overnight for later consumption.
Product Warranty Information
TEA TIPS
1.Store tea bags in a dark, cool and dry place away from strong odors and moisture. Do not refrigerate.
2.Never hold finished brewed tea for more than eight hours at room temperature. Discard any unused tea after eight hours
3.Brew only enough tea that you reasonably expect to sell within a few hours.
4.To protect tea flavor and to avoid bacterial contamination and growth, clean and sanitize tea brewing, storage and dispensing equipment at least once a day.
The Wilbur Curtis Company certifies that its products are free from defects in material and workmanship under normal use. The following limited warranties and conditions apply:
3 Years, Parts and Labor, from Original Date of Purchase on digital control boards.
2 Years, Parts, from Original Date of Purchase on all other electrical components, fittings and tubing.
1 Year, Labor, from Original Date of Purchase on all electrical components, fittings and tubing.
Additionally, the Wilbur Curtis Company warrants its Grinding Burrs for Forty (40) months from date of purchase or 40,000 pounds of coffee, whichever comes first. Stainless Steel components are warranted for two (2) years from date of purchase against leaking or pitting and replacement parts are warranted for ninety (90) days from date of purchase or for the remainder of the limited warranty period of the equipment in which the component is installed.
All
CONDITIONS & EXCEPTIONS
The warranty covers original equipment at time of purchase only. The Wilbur Curtis Company, Inc., assumes no responsibility for substitute replacement parts installed on Curtis equipment that have not been purchased from the
Wilbur Curtis Company, Inc. The Wilbur Curtis Company will not accept any responsibility if the following conditions are not met. The warranty does not cover and is void under the following circumstances:
1)Improper operation of equipment: The equipment must be used for its designed and intended purpose and function.
2)Improper installation of equipment: This eq�
3)Improper voltage: Equipment must be installed at the voltage stated on the serial plate supplied with this equipment.
4)Improper water supply: This includes, but is not limited to, excessive or low water pressure, and inadequate or fluctuating water flow rate.
5)Adjustments and cleaning: The resetting of safety thermostats and circuit breakers, programming and temperature adjustments are the responsibility of the equipment owner. The owner is responsible for proper cleaning and regular maintenance of this equipment.
6)Damaged in�.
7)Abuse or neglect (including failure to periodically clean or remove lime accumulations): Manufacturer is not responsible for variation in equipment operation due to excessive lime or local water condi- tions. The equipment must be maintained according to the manufacturer’s recommendations.
8)Replacement of items subject to normal use and wear: This shall include, but is not limited to, light bulbs, shear disks, “0” rings, gaskets, silicone tube, canister assemblies, whipper chambers and plates, mixing bowls, agitation assemblies and whipper propellers.
9)Repairs and/or Replacements are subject to our decision that the workmanship or parts were faulty and the defects showed up under normal use. All labor shall be performed during regular working hours. Overtime charges are the responsibility of the owner. Charges incurred by delays, waiting time, or operating restrictions that hinder the service technician’s ability to perform service is the
responsibility of the owner of the equipment. This includes institutional and correctional facilities. The Wilbur Curtis Company will allow up to 100 miles, round trip, per
PARTS WILL BE ACCEPTED WITHOUT A RETURN MERCHANDISE AUTHORIZATION (RMA). RMA NUMBER MUST BE MARKED ON THE CARTON OR SHIPPING LABEL. All
| WILBUR CURTIS CO., INC. |
|
| 6913 Acco St., Montebello, CA |
|
| Phone: |
|
| Technical Support Phone: | |
| Web Site: www.wilburcurtis.com |
|
6 | FOR THE LATEST SPECIFICATION INFORMATION GO TO WWW.WILBURCURTIS.COM | |
| Printed in U.S.A. 1/06 | |
