MAINTENANCE

11.ACTUATOR SCRUB DECK UP- DOWN REMOVAL/REPLACEMENT

FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and set parking brake (If option is installed).

1.Remove front cover.

2.Remove clevis pin and rue ring from lower bracket of actuator; do not allow actuator barrel to rotate.

3.Disconnect actuator from wiring harness.

4.Remove upper clevis pin and rue ring from actuator bracket.

5.Reverse steps to install.

SCRUB DECK UP-DOWN ACTUATOR ADJUSTMENT

The actuator will need to be adjusted when replaced.

To adjust the actuator:

1.While holding actuator barrel to prevent it from spinning, apply power to the actuator such that it is fully extended. Positive power to white wire, and negative/ground to black. Limit switch within actuator will stop it.

2.Turn barrel out one or more full turns to assure that when it is retracted it will not bind against itself.

3.While holding actuator barrel to prevent it from spinning, apply power to the actuator such that it is fully retracted. Positive power to black wire, and negative/ground to white wire. Limit switch within actuator will stop it.

4.With actuator fully retracted, turn barrel in until it touches the base of the threaded shaft.

5.At the bottomed out position, turn the barrel out 1 1/2 turns, then enough more to allow connection to lift linkage.

6.Connect actuator to lift linkage.

7.Check travel of actuator during operation.

12.ACTUATOR SCRUB DECK IN-OUT REMOVAL/REPLACEMENT

FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and set parking brake (If option is installed).

1.Remove front cover.

2.Swing the deck to the fully open position. This will align the access holes in the deck plates so that the clevis pin can be removed.

3.Remove the clevis pin and rue ring from both ends of the actuator.

4.Disconnect actuator from wiring harness.

5.Reverse steps to install.

SCRUB DECK IN-OUT ACTUATOR ADJUSTMENT

The actuator will need to be adjusted when replaced.

To adjust the actuator:

1.While holding actuator barrel to prevent it from spinning, apply power to the actuator such that it is fully extended. Positive power to white wire, and negative/ground to black. Limit switch within actuator will stop it.

2.Turn barrel out one or more full turns to assure that when it is retracted it will not bind against itself.

3.While holding actuator barrel to prevent it from spinning, apply power to the actuator such that it is fully retracted. Positive power to black wire, and negative/ground to white wire. Limit switch within actuator will stop it.

4.With actuator fully retracted, turn barrel in until it touches the base of the threaded shaft.

5.At the bottomed out position, turn the barrel out 1/2 of a turn, then enough more to allow connection to linkage.

6.Connect actuator to linkage.

7.Check travel of actuator during operation.

4-12

SCX364 86037150 1/17/07

Page 29 Page 31
Page 30
Image 30
Windsor SCX364, 10052410 manual Actuator Scrub Deck UP- Down REMOVAL/REPLACEMENT, Scrub Deck UP-DOWN Actuator Adjustment
Page 29 Page 31

10052410, SCX364 specifications

The Windsor SCX364, model number 10052410, is a sophisticated commercial-grade carpet extractor designed to deliver exceptional cleaning performance and efficiency in various settings, including hotels, offices, and retail spaces. This powerful machine offers a range of features and technologies aimed at ensuring superior floor care while also promoting operator ease and comfort.

One of the standout features of the Windsor SCX364 is its advanced suction system, which utilizes a high-efficiency vacuum motor. This motor not only enhances the extractor's cleaning ability but also aids in quick drying times, minimizing downtime and disruption in busy environments. The SCX364 is equipped with a large-capacity recovery tank, allowing for extended cleaning sessions without the need for frequent emptying, making it ideal for large areas.

Another critical technology integrated into the SCX364 is its dual-brush agitation system. This system employs two rotating brushes that work in unison to effectively loosen and lift dirt, stains, and debris from carpets. This dual-action approach ensures thorough cleaning and is particularly effective on high-traffic areas that may be more severely soiled.

In terms of operator comfort, the Windsor SCX364 features an ergonomic design that includes an adjustable handle and easy-to-use controls. These features enable operators to maneuver the machine effortlessly, even in tight spaces. Additionally, the lightweight construction of the SCX364 promotes ease of transport, allowing for convenient relocation between different areas.

The SCX364 is also designed with versatility in mind. It can accommodate a variety of cleaning solutions, enabling users to tailor their cleaning approach to different carpet types and soil levels. Its adjustable solution flow control allows operators to regulate water and detergent usage, optimizing cleaning performance while conserving resources.

In summary, the Windsor SCX364, model 10052410, is a high-performance carpet extractor that combines innovative technologies and user-oriented design. With its efficient suction system, dual-brush agitation, and adaptable settings, it stands out as a reliable choice for maintaining clean and inviting carpets in professional environments. Whether for routine maintenance or deep cleaning, the SCX364 delivers exceptional results, ensuring that carpets remain in excellent condition.
Top Page Image Contents