Winegard MV-4000 manual Installing the Power Switch, Installing the Dome

Models: MV-4000

1 12
Download 12 pages 622 b
Page 9
Image 9

Installation

GPS installation —

10.The GPS antenna is pre-wired and has a 1 meter cable running through one of the connectors.

Determine location for GPS antenna. It is recom- mended you place the GPS antenna 3 feet from dome.

The recommended location for the GPS antenna is based on having a level location and a clear view of the sky for the best satellite signal acquisition. Do not secure GPS antenna to roof at this time.

IMPORTANT! The GPS must be located minimum of 3 feet away from obstructions on roof of vehicle. An- tenna must have a clear view of the sky for proper operation.

Cable entry installation —

1.Decide the best location for the cables to enter the vehicle, and the location of the switch and re- ceiver (see “Installing the switch and receiver”on page 10). Drill a 1/2” hole in the roof, push wires in- side. Make proper connections.

You must have filtered +12 VDC power source.

INSTALLING THE POWER SWITCH

1.Choose a location to install the MV-4000 power ON/OFF switch. Remember when selecting a location that you will need to run the +12VDC power cable from the MV-4000 to the switch. Be sure the switch is in the OFF position before continuing. See Figure 9 page 10.

Wall or panel mount: Drill 1-1/4” hole, pull wires through wall or panel.

Surface mount: Determine location and direction of box. Mount box and feed wire into one of the box open ings. Select plate cover (brown or white provided) and snap the rocker switch into the switch plate. Be sure switch is off!

2.Connect the ground wire from the vehicle and the BLACK ground wire from the MV-4000 together, using large yellow spade connector.

3.Connect the YELLOW spade connector to the silver spade on the switch.

4.Connect the RED wire from the MV unit to the small RED spade connector.

2.Place cable-entry plate over hole and cables. Screw in place. Seal plate and screw holes with ap- proved sealant (not included).

5.Connect small RED spade connector to center spade on switch.

6.Connect the +12 V power wire from the vehicle to a small RED spade connector.

3.Depending on the length of the cable on the roof, you may need to use cable clamps or wire ties (not provided) between the unit and your cable-entry plate. Clamping the cable every 12”-16” should eliminate any unnecessary cable movement, Figure 6.

 

CABLE-

CABLE

FIGURE 4

ENTRY

CLAMPS

7.Connect small RED spade connect to isolated spade on switch.

INSTALLING THE POWER SWITCH DIAGRAM

FIGURE 5

ON/OFF ROCKER SWITCH

WITH LIGHT

(Shown in OFF position.)

INSTALLING THE DOME

Insert screw in holes on dome rim. Be sure bolt is vertical; not tilted to side. Place nut under rim and tighten.

CAUTION:

DO NOT

OVERTIGHTEN!!

QUADREX SCREW WITH WASHER (USE #2

PHILLIPS)

STEPS 2 & 3

STEPS 6 &7

TWO GROUND WIRES

+12 V FROM VEHICLE

1 FROM VEHICLE

 

1 BLACK WIRE FROM

 

SATELLITE DISH

STEPS 4 & 5

 

 

RED POWER

 

WIRE FROM

 

DISH

Terminals on switch have to be bent to fit in surface mount box.

9

Page 9
Image 9
Winegard MV-4000 manual Installing the Power Switch, Installing the Dome

MV-4000 specifications

The Winegard MV-4000 is a modern outdoor TV antenna designed for optimal performance and reliability. As cord-cutting trends continue to rise, the demand for robust antennas that offer excellent reception has increased, and the MV-4000 stands out with its advanced features and technologies.

One of the key characteristics of the Winegard MV-4000 is its high gain of up to 60 miles, allowing users to receive over-the-air broadcast signals from a significant distance. This capability makes it an ideal choice for both urban and suburban environments, where signal reception can vary based on geographic location and obstructions.

The MV-4000 employs a combination of digital and analog technology to deliver superior picture quality. It includes a built-in low-noise amplifier (LNA) that enhances weak signals, reducing the chances of pixelation or signal drop-out. This amplifier is especially beneficial in areas with challenging terrain or far from transmission towers.

Constructed with durability in mind, the Winegard MV-4000 features a rugged design capable of withstanding harsh weather conditions. Its robust housing is resistant to corrosion and features UV protection, ensuring that the antenna maintains its integrity over time. This longevity is a significant advantage for users looking for a long-term solution for their television viewing needs.

The MV-4000 is also versatile in installation, allowing for both roof and wall mounting. This flexibility ensures that users can find the optimal location to capture signals without too much hassle. The antenna also includes a 360-degree rotation capability, which helps in adjusting the directional reception as needed, further enhancing its performance.

Another noteworthy feature of the MV-4000 is its compatibility with a range of devices. It can be easily connected to various TVs, DVRs, and streaming devices. This adaptability makes it an attractive option for consumers who want to enhance their viewing experience without investing in expensive cable packages.

In summary, the Winegard MV-4000 is a feature-rich outdoor antenna that combines high gain reception, advanced technology, and durability. With its focus on providing an excellent over-the-air viewing experience, it caters to a wide range of users looking to ditch cable while still enjoying quality television content. Whether you live closer to urban centers or in more remote locations, the MV-4000 is equipped to meet your digital broadcasting needs effectively.