STEP 3. Attach dish to backup. Use bolts and nuts provided, Figure 4.

STEP 4. Mount dish on roof in upright position. Rotate clockwise to stop, Figure 5. Dish will be toward back of vehicle when in stowed or travel position. The word FRONT is embossed on the base and should face the front of vehicle. Secure to roof using screws (provided). The travel bracket sjhould be mounted to roof 6-1/8” from base of dish, toward back of vehicle. See Figure 6.

NOTE: Apply non-hardening sealing compound to screw heads, coax access hole and edge of gasket under mount base.

Install the vent tube on the back of the mount base (the is the side opposite the word FRONT). The hole for the vent tube is shown in Figure 6A. CAUTION: DO NOT seal hole in vent tube. Put sealant around the outside of the vent tube, approximately 1/2” from end. Push vent tube into the hole. The sealant will seal the hole as you push in vent tube. Leave approxi- mately 2 to 2-1/2” of the vent tube extending from the hole. Put a small amount of sealant on the roof under the vent tube end to hold in place.

FIGURE 6

Base Plate

(4)Antenna Mounting Bolts

FIGURE 4

FIGURE 5

Measure 24” of coax at plastic fastener on left side of feed arm. (See Step 5.)

No cable clamps on this part of cable.

Install cable entry plate 3” minimum from mount base.

(4)1/4-20

HEX NUTS

Rotate clockwise to stop.

FIGURE 6A

CAUTION: DO NOT GET sealing compound between Base Plate and Rotating Gear Housing. DO NOT PAINT top of Base Plate or around Rotating Gear Housing.

STEP 5. Facing the front of the dish, note the coax attached to the side of the feed arm. Meaure 24” coax from this point. DO NOT CUT. Put coax around mount base, Figure 5.

ANOTHER METHOD OF IBSTALLING ROOF/CABLE ENTRY PLATE: Attach cable to roof using cable clamp. Use sealant to seal screw heads.

STEP 6. Apply approved sealing compound over mounting screw heads.

STEP 7. Feed coax through the roof using cover plate (included, w/hardware), Figure 7. Weatherproof cable entry by applying sealant under lip of cable entry plate and where cable enters roof. Attach plate to roof with screws provided. Apply sealant over screws and around edge of roof-thru plate, making sure cable en- try is sealed. If downlead connection is made on top of roof, make sure to weatherproof connection!

#10 x 1” Screws

FIGURE 7

Downlead connects to satellite receiver

CE-2000

Downlead

FS-8100

Male-to-male

F-connector

Rev. 6/06/03

6

 

Page 5 Page 7
Page 6
Image 6
Winegard RM-DM00, RMDM04, RMFLDM4, RM-DM46 manual HEX Nuts
Page 5 Page 7

RMFLDM4, RM-DM46, RMDM04, RM-DM00 specifications

Winegard is a well-known manufacturer of advanced antenna technology, and its products are designed to provide high-quality reception for broadcast television. Among its lineup, the Winegard RM-DM00, RMFLDM4, RMDM04, and RM-DM46 antennas stand out for their exceptional features and efficiency.

The Winegard RM-DM00 is a compact, multi-directional antenna that is engineered for optimal performance in urban areas with significant electronic interference. Its unique design allows it to capture over-the-air signals from multiple directions, ensuring a robust signal and exceptional picture quality. With a sleek and discreet profile, the RM-DM00 can be easily mounted on rooftops or exterior walls, offering versatility in installation options.

Next in line, the RMFLDM4 is a flat antenna known for its ultra-thin design and no-obstruction capabilities. This antenna employs advanced filtering technologies that minimize noise and enhance signal clarity. Its sleek aesthetic makes it an ideal choice for modern interiors, allowing homeowners to place it in living rooms or offices without disrupting the decor. The RMFLDM4 is engineered to pick up both VHF and UHF channels, making it a versatile choice for users in various regions.

The RMDM04 is a durable and weather-resistant model designed for outdoor usage. This antenna is perfect for those living in rural areas, where signal ranges can be challenging. Equipped with advanced amplification technology, the RMDM04 can extend the range of signal reception enough to capture long-distance broadcasts, ensuring viewers enjoy uninterrupted access to their favorite channels, even in remote locations.

Lastly, the RM-DM46 is designed for superior performance, boasting dual UHF/VHF reception capabilities. This model includes a built-in signal amplifier that boosts weak signals while reducing noise for the ultimate viewing experience. The RM-DM46 is versatile and easy to install, compatible with most devices, making it a favorite among cord-cutters who wish to access free, high-quality television content.

Overall, each of these Winegard antennas—RM-DM00, RMFLDM4, RMDM04, and RM-DM46—offers unique features and technologies designed to maximize signal reception while ensuring reliability and ease of use. Whether for urban settings or rural landscapes, Winegard's antennas effectively enhance viewers' experiences, allowing them to enjoy a diverse range of channels with excellent picture quality. With these options, users can find the perfect match for their television needs, underscoring Winegard's commitment to innovation and performance in the antenna market.
Top Page Image Contents