MODEL 801642
ROOF MOUNT INSTALLATION | Page 2 |
|
For use with Models CTWH30, CTWH36, IH4227, DD30R, DD36R, DD45R,
PREPARE THE ROOF |
| WIRE THE VENTILATOR | |||
|
|
|
| 5 Remove 10 |
|
| 15" |
|
| COVER SCREWS |
|
|
|
| and lift off |
| |
|
|
|
| ventilator cover. |
|
| 1¼" dia. hole |
|
| 6 Feed the electric |
|
|
|
| power cable | GROUND | |
|
|
|
| through the 1¼" | TO |
| REMOVE SHINGLES |
| GROUNDING | ||
|
| DIAMETER HOLE | |||
1211/16" | 1" | SCREW | |||
RoofRafter | RafterRoof | and connect cable |
| ||
|
| WHITE TO BLUE, |
| ||
|
|
|
| to ventilator with a | WHITE |
|
|
|
| proper connector | |
|
|
|
| for the type of | TO |
|
|
| 20½" | cable being used. |
|
|
|
|
| 7 Connect BLACK |
|
|
|
|
| TO BLACK, | 120 |
|
|
|
|
| |
Pilot Hole |
|
| and GROUND | VAC | |
11" dia. |
| LINE | |||
(centered |
| TO GROUNDING | IN | ||
|
|
|
|
| |
between rafters) | hole |
| SCREW. | BLACK TO BLACK | |
|
|
|
|
| |
| 913/ 16" |
|
| INSTALL THE VENTILATOR | |
|
|
|
| ||
| 18" |
|
| Drill 6 | |
|
|
|
|
| |
|
|
|
| 10 Cover | Mounting |
|
|
|
| Holes | |
From inside the attic space: |
|
| Screws | ||
|
|
| |||
1 Drill a PILOT HOLE up through the roof, centered between |
|
| |||
ROOF RAFTERS. |
|
|
|
| |
From outside - on the roof: |
|
|
| Remove | |
|
|
| roofing | ||
2 Measure and mark the 18" x 20½" rectangle. Cut and remove |
| ||||
| nails from | ||||
only the shingles inside this rectangle. |
|
| top 2/3 of | ||
3 Measure and mark the 11" DIAMETER HOLE and the 1¼" |
| ||||
Flashing | shingles. | ||||
DIAMETER HOLE. Cut these holes all the way through the |
| ||||
roof. |
|
|
| Sheet |
|
|
| 2" |
|
| Damper |
|
|
|
|
| |
| " |
|
| Bird Screen | |
| 29½ |
|
| ||
|
|
|
|
| |
|
|
| 7" |
|
|
|
|
|
| OUTSIDE - ROOF VIEW | |
22 |
|
|
| 8 Remove roofing nails from top 2/3 of shingles around | |
" |
|
|
| ||
|
|
| 9 Slide the ventilator's FLASHING SHEET up and under | ||
|
| 2" |
| ||
|
|
| the loosened shingles until ventilator's discharge collar | ||
|
|
|
| fits into 11" diameter hole. | |
For flat roof installations: |
|
| 10 Use the 6 screws (provided) to attach the ventilator | ||
4 Build a curb that will mount the blower at a minimum pitch of | to the roof. DRILL 6 MOUNTING HOLES inside the | ||||
ventilator, as necessary. | |||||
2/12. Discharge end of the blower should be pointed away | 11 Seal the screw heads, loosened shingles, and edges of | ||||
from prevailing winds. |
|
| |||
|
| the flashing sheet, with a good grade of roofing cement. | |||
|
|
|
| ||
|
|
|
| 12 Check for free movement of the | |
|
|
|
| DAMPER, and | |
|
|
|
| power and check operation. |