Lift Chain Hook-Up Table
Mower Model |
| Chains Used | Lift Chain Attach Plt | Holes Used for Spring | Special | |||
Number |
| Notes | ||||||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| Part No | No Used | Description | To Lift | To Holes in | Upper End to | Lower End to |
|
|
|
|
| Lever Hole | Mower | Hole Let- | Hole Let- |
|
|
|
|
|
|
| tered: | tered: |
|
|
|
|
|
|
|
|
|
|
42A, HB | 4154 | 1 | 33 Link Chain | B | H&G | O | See note 4 | (10) |
|
|
|
|
|
|
|
|
|
L42AC, B&C | 4154 | 1 | 33 Link Chain | B | G | P | H | (5) |
|
|
|
|
|
|
|
|
|
42C | 4154 | 1 | 33 Link Chain | B | L&M | See note (8) | Z | (8) |
|
|
|
|
|
|
|
|
|
L42U | 17477 | 1 | 84" Twisted | B | H | T | H |
|
|
|
| cut off excess |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
L42VAC | 6673 | 1 | 78" Twisted | B | H | R | J |
|
|
|
|
|
|
|
|
|
|
L42VC | 4154 | 1 | 33 Link Chain | B | G | S | J |
|
|
|
|
|
|
|
|
|
|
L59A, 59HB, | 4154 | 1 | 33 Link Chain | A or B | E | N | C&D | (1, 3, 8, 10) |
& L306A | 18264 | 1 | 13 Link Chain | Opt | E | N | C&D | (1, 3, 8, 10) |
|
|
|
|
|
|
|
|
|
59HC | 18264 | 3 | 13 Link Chain | A or B | E | N | C&D | (1, 3, 8, 9) |
|
|
|
| Opt |
|
|
|
|
|
|
|
|
|
|
|
|
|
L59AC, B&C | 4154 | 1 | 33 Link Chain | A | C&D | Q | E | (5) |
L306AC, B&C | 18264 | 1 | 13 Link Chain | A | C&D | Q | E | (5) |
|
|
|
|
|
|
|
|
|
59C | 4154 | 2 | 33 Link Chain | A | C&D | See note (8) | See note (1,3) | (8) |
|
|
|
|
|
|
|
|
|
L59U, L306U | 17477 | 1 | 84" Twisted | B | C&D | T | See note (3) | (1) |
| 18264 | 1 | 13 Link Chain | B | C&D | T | See note (3) | (7) |
|
|
|
|
|
|
|
|
|
L59VAC, | 17477 | 1 | 84" Twisted | B | E | R | E | (7) |
L306VAC |
|
|
| B | U | R | E |
|
|
|
|
|
|
|
|
|
|
L59VC, | 4154 | 1 | 33 Link Chain | B | E | S | C&D | (1, 3, 8) |
L306VC | 18264 | 1 | 13 Link Chain | B | U | S | C&D | (7) |
|
|
|
|
|
|
|
|
|
Special Notes (Refer to numbers in parentheses in above table)
1.Hook one
2.Fasten one
3.Hook lower end of spring in crotch chain.
4.Hook spring into chain just above hole “H”.
5.Clamp offset end spring under flat washer on
6.Fasten two
7.On L306 models, use heavy spring furnished with mower rather than lighter spring furnished with manual lift kit. Hook to a point on tractor so most of mower weight is held by spring which will allow lift to work easier.
8.Hook upper end of spring over bushing (4). Bolt lift chain to lift lever with 3/8 x 2 bolt and nut.
9.Bolt two
10.On IH “A” lift lever (3) goes inside steering rod. On IH “B” it goes outside steering rod. For IH “B” shim attachment plate (10) out away from tractor using spacer (11), four washers (56) and bolts (38). Lift lever may have to be bent out slightly to clear steering rod.
26 Parts | 29931 (Rev. 6/29/2007) |
|
|
