ATTACHING CUTTER TO TRACTOR (PULL-TYPE MODELS)

The cutter is shipped with a 1-3/8" PTO spline. The horizontal distance between the end of the tractor PTO shaft and the drawbar hitch point should be 14". This distance must not vary more than plus or minus one inch (±1") or the drive may be damaged when turning. Adjust tractor drawbar to obtain the desired drawbar to hitch point distance. On some tractors, a drawbar kit must be used to obtain the required dimension. Check with your tractor dealer if you encounter problems.

Raise cutter tongue to tractor drawbar height with jack provided and attach with a 3/4" or larger high-strength drawbar pin. Retain pin to keep it in place.

Connect cutter driveline to tractor PTO shaft, making sure the spring-activated locking pin slides freely and is seated firmly in tractor PTO spline groove.

Adjust H-frame bearing height to ensure front driveline is parallel to ground.

Remove parking jack from tongue. Attach to frame rail storage with top forward. Always attach jack to tongue to hold it up when disconnecting it from tractor.

Adjust drive shaft carrier bearing (2), Figure 6, verti- cally in H-frame until driveline is as straight as possible between tractor PTO and cutter gearbox.

Cutting Height Adjustment for D80 Pull-Type Cutter (Figure 6)

Place tractor and cutter on a level surface.

Cutting height is raised and lowered with height adjust- ment crank (3) or optional hydraulic cylinder. Front to rear attitude is set with the compression link (1). The blade is approximately 9-1/4" below cutter deck. Select a cutting height, EXAMPLE 3".

Raise front end of deck with a jack to take the compres- sion member (1) out of compression and remove the bolt connecting it to the tongue.

Raise front end of deck until both sides are 12-1/4" above the ground and block underneath to maintain this distance.

Raise rear end of deck until it is from 13-3/4" to 14" above the ground.

Connect compression member (1) to tongue. It may be necessary to raise or lower rear of deck to align hole.

Remove the blocks from under the deck and position each side skid 1/2" above the ground.

This complete procedure must be followed to properly set a new cutting height. Raising rear of deck with crank without changing the compression link position will result in an incorrect front-to-rear attitude setting.

1. Compression member

M3866

 

2.

Carrier bearing

 

3.

Adjustment crank

 

 

 

 

Figure 6. Cutting Height Adjustment - D80

(Pull-Type Model)

PRE-OPERATION CHECK LIST

(Owner’s Responsibility)

___ Check that cutter is properly and securely attached to tractor.

___ Make sure driveline spring-activated locking pin slides freely and is seated firmly in tractor PTO spline groove.

___ On pull-type cutter, make sure the pin to prevent crank detachment is installed.

___ Set tractor PTO at 540 rpm.

___ Make sure gearbox is full to fill plug with SAE 90W gear lube.

___ Lubricate all grease fitting locations.

___ Check that all hardware is properly installed and secured.

___ Check to ensure blades are sharp and secure and cutting edge is positioned to lead in a counter-clockwise rotation.

___ Check that all shields and guards are properly installed and in good condition.

___ Check cutting height and attitude adjustment.

___ Place tractor PTO and transmission in neutral before attempting to start engine.

___ Inspect area to be cut and remove stones, branches or other hard objects that might be thrown, causing injury or damage.

___ Inspect chain shielding and replace any damaged or missing links.

STARTING AND STOPPING CUTTER

Cutter operating power is supplied from tractor PTO. Refer to your tractor manual for PTO engagement and disengagement instructions. Always operate PTO at 540 rpm. Know how to stop tractor and cutter quickly in case of an emergency.

When engaging PTO, the engine rpm should always be low. Once engaged and ready to start cutting, raise PTO speed to 540 rpm and maintain throughout cutting operation.

16 Operation

15916 (Rev. 3/30/2007)

 

 

Page 15 Page 17
Page 16
Image 16
Woods Equipment MDO80-2 manual Attaching Cutter to Tractor PULL-TYPE Models, PRE-OPERATION Check List
Page 15 Page 17

DO80-2, MDO80-2 specifications

The Woods Equipment MDO80-2 and DO80-2 are robust and innovative pieces of machinery designed to meet the demands of both commercial and agricultural applications. Renowned for their efficiency and performance, these models have garnered attention for their advanced features and technologies that enhance productivity.

One of the standout characteristics of the MDO80-2 and DO80-2 is their powerful cutting capabilities. Equipped with a heavy-duty steel frame, both models provide exceptional durability, allowing them to withstand rigorous use in various conditions. The cutting decks are designed for superior grass trimming, reducing the need for multiple passes and saving valuable time. The adjustable cutting height offers versatility, accommodating different grass types and lengths, ensuring a flawless finish every time.

Another key feature of these models is their advanced blade technology. The blades are crafted from high-quality steel, increasing their longevity and performance. The designs enable clean cuts, promoting healthier grass growth and enhancing the overall appearance of lawns and fields. Additionally, the MDO80-2 is equipped with a double-blade system, which further enhances cutting efficiency and reduces clumping.

The MDO80-2 and DO80-2 also prioritize user comfort and ease of operation. They come with ergonomic controls that ease the strain on operators during extended use. The intuitive design of the control panel simplifies operation, allowing users to focus on their tasks without getting bogged down by complicated settings.

For enhanced maneuverability, both models feature a smooth turning radius, making them ideal for navigating tight spaces. Whether working in a residential yard or a larger agricultural field, operators benefit from the agility these machines provide.

In terms of maintenance, Woods Equipment has developed the MDO80-2 and DO80-2 with user-friendliness in mind. The models are designed for easy access to critical components, simplifying routine maintenance tasks. This design philosophy not only prolongs the lifespan of the equipment but also minimizes downtime.

Overall, the Woods Equipment MDO80-2 and DO80-2 are exceptional choices for those seeking high-performance mowing solutions. With their durable construction, advanced cutting technologies, and user-friendly features, these models are well-suited for fulfilling the demands of any mowing operation, making them a reliable investment for years to come.
Top Page Image Contents