ASSEMBLY

Assembly of this rotary tiller is the responsibility of the WOODS dealer. It should be delivered to the owner completely assembled, lubricated and adjusted for nor- mal conditions.

„Do not allow bystanders in the area when oper- ating, attaching, removing, assembling, or servic- ing equipment.

„Do not modify or alter or permit anyone else to modify or alter the equipment or any of its compo- nents in any way.

CAUTION

„Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

SET-UP INSTRUCTIONS

The rotary tiller is shipped partially assembled. Assem- bly will be easier if components are aligned and loosely assembled before tightening hardware. See “Bolt Torque Chart” on page 37 for recommended torque values.

Complete the Pre-Delivery and Delivery Check Lists on page 26 when assembly is complete.

Select a suitable working area. Refer to illustrations, accompanying text, parts lists, and exploded view drawings.

For reference, front, back, left, and right directions are determined by sitting in the tractor operator’s seat.

DISASSEMBLE SHIPPING UNIT

It is advisable to have a mechanical lifting device to facilitate uncrating.

Be careful of nails in boards when uncrating.

1.Remove all parts that are wired and strapped to tiller and/or crate.

2.Remove top, sides, and ends of crate.

3.Remove front rubber shield from the bottom of the crate (reverse rotation models only).

4.Remove lag screws from L-shaped shipping brack- ets. Remove L-brackets from the tiller. Be sure to save the mounting hardware for later use.

5.Remove tiller assembly from crate base.

6.Remove loose nails from boards and dispose of crate according to local codes.

ASSEMBLY PROCEDURES

Required tools: 9/16", 3/4”, 1-1/8" combination wrenches, sockets, torque wrench, and jack stands.

1.Lower skid shoes to lowest position and stand tiller upright.

2.Use jack stands to support the front frame tube with tiller sitting on the ground.

3.Install parking stand (33) and spring assembly to tiller frame using 1/2NC x 3-1/4 cap screw (67) and flange nut (62).

4.Unbolt lower hitch clevises (34), rotate 90 degrees and re-install in operating position, 26" from center to center. Figure 23, page 25.

5.Install driveline (8) to gearbox input shaft.

6.Attach mast plates (27 & 28) and driveline holder

(80)to gearbox frame using 3/8NC x 1 serrated flange screws (55) and flange whiz nuts (60). Attach driveline holder on outside of mast plate using the front two holes. Figure 23, Page 25.

7.Install CAT 1 quick hitch sleeve (70) using 3/4NC x 3-1/2 cap screw (68) and lock nut (69). Install in the lower hole in the top of the mast plates.

8.Attach driveline tether chain to the tiller hitch frame.

9.Attach tailgate chain lug on tailgate using packing slip instructions in hardware bag. Thread the chain through the keyhole slot on the top safety shield support. Secure the chain by sliding the desired link into the narrow portion of the keyhole slot.

Figure 22. Attaching Tailgate Chain

10.Attach front rubber deflector and clamp bar using 5/16NC x 1 carriage bolts (53) and flange whiz nuts (54). (Reverse models only)

11.Fill gearbox with SAE 80W or 90W gear lube until it runs out the side level plug

NOTE: Chain case has .8 quarts of 00 grease installed at factory. This grease is very viscous and will stick to chain at 70°F.

24Assembly

(Rev. 8/4/2011) MAN0814 (3/11/2010)

Page 23 Page 25
Page 24
Image 24
Woods Equipment TS52, TS44 manual SET-UP Instructions, Disassemble Shipping Unit, Assembly Procedures
Page 23 Page 25

TS44, TS52 specifications

Woods Equipment has long been a trusted name in the lawn and landscape industry, and their TS52 and TS44 models showcase the brand's commitment to quality and performance. These front-mounted snow throwers are designed for use with compact tractors, offering a robust solution for snow removal and ground maintenance tasks.

The TS52 is a powerful 52-inch snow thrower, while the TS44 offers a slightly more compact 44-inch option. Both models feature durable construction, ensuring they can withstand the rigors of demanding winter conditions. Made from high-strength steel, these snow throwers boast a rugged build that prioritizes longevity, making them ideal for both residential homeowners and commercial operations.

One of the standout features of the TS series is the efficient drive system. Equipped with a heavy-duty auger and impeller, these machines deliver exceptional performance in snow removal, even in deep or heavy conditions. The auger design ensures optimal snow intake, while the impeller efficiently throws snow up to 30 feet away, maximizing clearing efficiency.

Both models come with adjustable skids that allow users to customize their height settings for varying surface conditions. This versatility is essential for different applications, whether clearing driveways, sidewalks, or larger areas. The TS52 and TS44 are also equipped with electric lift capabilities, allowing for effortless attachment and detachment from the tractor.

In terms of technology, Woods has integrated features that enhance usability and control. The easy-to-use controls allow operators to adjust the chute direction effortlessly, providing precise snow placement. This is particularly valuable in busy areas where clearing snow effectively while minimizing obstruction is crucial.

The TS series snow throwers are designed with user comfort in mind. Their ergonomic controls and balanced design contribute to a more pleasant operating experience, reducing fatigue during extended use. Additionally, the machines are compatible with a variety of compact tractors, making them a flexible choice for different users.

In summary, the Woods Equipment TS52 and TS44 snow throwers represent a blend of durability, efficiency, and user-friendly design. With their robust construction, innovative technologies, and adaptable features, these snow throwers are poised to tackle winter’s challenges, ensuring users can maintain clean, safe surfaces throughout the snow season. Whether for personal use or commercial applications, the Woods TS series delivers performance that snow removal professionals and homeowners alike can rely on.
Top Page Image Contents