Xantech YiAK-K1000-01A manual Step Two Install an Optional IR Sensor, Terminal Block Ribbon Cable

Step Two – Install an Optional IR Sensor

If you are installing the optional IR sensor, you also need to prepare the sensor’s ribbon cable. The recommended Xantech 490-00 Micro Link comes with a 7-foot long, 3-con- ductor ribbon cable. Trim the ribbon cable to 3 or 4 inches. Strip the wire ends 1 to

1-1/2 inches, then fold each bare end over itself twice and twist it. This creates a slightly thicker wire to connect to the KP 1‘s IR Sensor Terminal Block 4. Break out the IR Sensor Cutout 5 on the front of the KP 1 by gently pressing out, and insert the Micro Link sensor through the hole from the front, cable end first. Install the sensor’s nut on the threaded body of the sensor before connecting the ribbon cable to the

KP 1’s terminal block. Tighten the nut to secure the sensor in its cutout.

490-00IR Receiver

Decorator

Cover

Plate &

2Screws (not included)

RJ-45 Connector (cable not shown)

Front

Panel

J-Box

Wallboard

1/8" x 3/4" Machine

Screws (2) (included)

Red (or White)	OUT
Stripe
	+12V
	GND

7’ Ribbon Cable

Copyright 2000 Xantech Corporation

Figure 2

Figure 3

Rear of PA 4000

h g f ed c

Carefully connect the bare ends of the sensor’s three wires to the KP 1 Terminal Block ¢ as shown in Figure 2 and Wiring Chart 2. Loosen the set screw for each ter- minal position, insert the end of the bare wire into the hole directly under the corre- sponding set screw, and tighten the set screw, making sure that no wires touch each other or other terminals. If a different compatible IR sensor is used, match the wire color used to the specific circuit function. Then connect the wires to the KP 1 Terminal Block ¢ in accordance with Wiring Chart 2.

POWER CONTROL MODE

AMP MODE

CH4

BRIDGE

2 CH3

CH2

BRIDGE

1 / CH1

AC/DC

ON/

AC/DC

ON/

AC/DC

ON/

AC/DC

ON/

TRIG.

KEYPAD

TRIG.

KEYPAD

TRIG.

KEYPAD

TRIG.

KEYPAD

BRIDGE 2

BRIDGE 1

MUSIC

MUSIC

MUSIC

MUSIC

NORMAL

NORMAL

SENSE

SENSE

SENSE

SENSE

CH3/4

CH1/2

VOLUME

KEYPAD IN

CH4

CH3

CH2

CH1

CH4

CH3

CH2

DN

UP

DN

UP

DN

UP

DN

UP

3-30V

AC/DC

TRIGGER

INPUT

CH1

CH 3 IN			MAIN
		CH3
		SEPARATE
		ON
		OFF
	REMOTE IR SENSOR IN		REMOTE
			CONTROL OUT
CH4	CH3	CH2	CH1

MR ON/OFF COMMAND

ON OFF

Position on KP 1	Position on Micro Link	Circuit Function
Terminal Block	Ribbon Cable
Right	Middle	+12 Volts
Middle	Red or White Stripe on	IR Signal (Output
	Outside of Ribbon	of Micro Link)
Left	Opposite to Stripe	Ground
Wiring Chart 2

No other connections are required, as the terminal block is internally connected to the KP 1’s RJ-45 Connector £ for connections to the PA 4000 and onward to other IR- controlled devices as applicable.

Step Three – Install the KP 1 In the Wall

Although the KP 1 is designed to fit into a standard single-gang electrical junction box or plaster ring, always check the fit before cutting into a wall. Follow these guidelines for optimal placement of the KP 1:

CAUTION: THE ELECTRICAL JUNCTION BOX IN WHICH THE KP 1 IS MOUNTED MUST BE DEDICATED TO LOW-VOLTAGE CONTROL SYSTEM APPLICATIONS. MAKE SURE THAT NO AUDIO/VIDEO OR AC MAINS WIRING PASSES THROUGH OR TER- MINATES IN THIS BOX!

If you install the optional IR sensor, avoid placing the KP 1 in an area subject to poten- tial interference with the IR signal.

Locate the KP 1 at least 4 inches from a dimmer switch, or install it inside a metal box rather than plastic, as the dimmer switch may generate electronic noise that might interfere with the KP 1.

The KP 1 may be installed in a multi-gang junction box with other low-voltage controls. Please refer to Figure 3 for guidance in installing the KP 1 into a junction box and attaching a Decora-style cover plate.

Gently place the KP 1 in the junction box or plaster ring and attach it by inserting the supplied mounting screws through the Mounting Screw Slots ™ of the KP 1 until it is aligned correctly and tighten the screws.

Attach a Decora-style cover plate (not included) by placing the screws provided with the cover plate through the plate’s holes and into the KP 1’s Cover Plate Screwholes ¡. Hand-tighten the screws so that the cover plate is secure, taking care so as not to overtighten and break the cover plate. Although any color or compatible style of wall plate may be used with the KP 1, the KP 1 itself should not be painted, in order not to cover the printed button labels.

	CH3	CH1
BRIDGE 2	BRIDGE 2 BRIDGE 1	BRIDGE 1
	CH4	CH2

a b

aIR Remote Control Output b MR On/Off Command Switch c Remote IR Sensor Inputs d Remote Keypad Inputs

e Bridge 1 Amplifier Mode Switch f Bridge 2 Amplifier Mode Switch g Power Control Mode Switches h Volume/Output Level Controls

Step Four – Connect the KP 1 to the PA 4000

•When the PA 4000 is used in the Normal mode, feeding four pairs of speakers, con- nect the cable from each KP 1 to the Remote Keypad Input d corresponding to the proper speaker channel for that room.

•When the PA 4000 is used in one of the Bridged modes, connect the cable from the KP 1 to the Remote Keypad Input d corresponding to the lower numbered jack for the pair of channels being bridged. Thus, when Output Channels 1 and 2 are bridged, connect the KP 1 cable to the Remote Keypad Input d connector for Channel 1. When Channels 3 and 4 are bridged, connect the KP 1 cable to the Remote Keypad Input d connector for Channel 3.

•The proper Remote Keypad Input d connections are determined by whether the amplifier channels are used in their Normal mode or if they are bridged. Use of a separate input source for Channel 3 does not impact the keypad connections.

•When a KP 1 is connected to any Remote Keypad Input d, the Power Control Mode Switch g for that channel must be placed in the far right position, under the words “ON/KEYPAD” to enable the KP 1’s Power Button 3 to turn on the

PA 4000.