Manuals / Brands / Home Audio / Speaker System / Yamaha / Home Audio / Speaker System

Yamaha AVX-S80 Installing the speakers, ■Placing the center speaker, ■Placing the front and rear speakers, ■Mounting the front and rear speakers on a wall

1 55

Download 55 pages, 944.54 Kb

SPEAKER SETUP

Installing the speakers

■Placing the center speaker

Place the speaker on TV whose top is flat or on the floor under the TV or inside the TV rack so that it is stabilized. When placing the speaker on top of the TV, to prevent the speaker from falling down, put the provided fasteners at two points on the bottom of the speaker and the top of the TV.

Fastener

Peel off the seal

Cautions

•Do not place the speaker on top of the TV whose area is smaller than the bottom area of the speaker. If placed, the speaker may drop out causing an injury to you.

•Do not place the speaker on top of the TV with an inclination.

•Do not touch the adhesive surface after peeling off the seal as this will weaken its adhesive strength.

•Thoroughly wipe clean the surface where the fastener is to be applied. Note that adhesive strength is weakened if the surface is dirty, oily or wet and that this may cause the center speaker to drop.

■Placing the front and rear speakers

When placing the front and rear speakers on a flat surface, attach the included non-skid pads to the corners on the bottom of the speakers as shown below. This prevents the speakers from sliding around.

Non-skid pad

■Mounting the front and rear speakers on a wall

When mounting the speakers on a wall, use the holes on the speakers’ back panels.

1 Fasten screws into a firm wall or wall support as shown in the figure.

Tapping screw

(Available at the

hardware store)

Diam. 3.5 to 4 mm

Wall/wall

support

70 mm

70 mm

10 mm

Min.

20 mm

2 Hang the holes on the protruding screws.

Make sure that the screws are securely caught by the narrow parts of the holes.

70 mm

Warning

• Each speaker weighs 0.9 kg (11 lbs. 16 oz.). Do not mount them on thin plywood or a wall with soft surface material. If mounted, the screws may come out of the flimsy surface and the speakers may fall. This damages the speakers or causes personal injury.

• Do not install the speakers to a wall with nails, adhesives, or any other unstable hardware. Long-term use and vibrations may cause them to fall.

• To avoid accidents resulting from tripping over loose speaker cables, fix them to the wall.

• Select a proper position on the wall to mount the speaker so that no one will injure his/her head or face.

10

Contents

HOME THEATER SOUND SYSTEM IMPORTANT SAFETY INSTRUCTIONS CAUTION FCC INFORMATION (for US customers) We Want You Listening For A Lifetime CONTENTS INTRODUCTION FEATURES ■About this manual CHECKING THE ACCESSORIES INSTALLING BATTERIES IN THE REMOTE CONTROL ■Notes on batteries CONTROLS AND FUNCTIONS Front panel Remote control ■Using the remote control Front panel display PREPARATION STEPS SPEAKER SETUP Speaker placement Installing the speakers ■Placing the center speaker ■Placing the front and rear speakers ■Mounting the front and rear speakers on a wall ■If you want to mount a speaker on a commercially available speaker stand CONNECTIONS components ■Types of audio jacks ■Type of video jacks ■The connection example Connecting the antennas ■Connecting indoor FM antenna ■Connecting the AM loop antenna Connecting the speakers ■Using commercially available speakers and speaker cables Connecting to an external amplifier Connecting the AC power cord ■ Memory back-up Turning on the power ADJUSTING SPEAKER OUTPUT LEVELS Using the test tone BASIC PLAYBACK Basic operations ■Enhancing the bass tones ■To mute the sound ■When you have finished using this system ■Setting the sleep timer ■Input modes and indications Selecting a sound field program ■Feature of DSP programs Page ■Table of Program Names for Each Input Format ■Selecting PRO LOGIC ■Playing Dolby Digital Surround EX or DTS ES software ■Virtual CINEMA DSP ■SILENT CINEMA DSP ■Normal Stereo Reproduction ■Displaying the information about input signal ■About 96-kHzsampling digital signals RECORDING ■Timer playback/recording TUNING Automatic and manual tuning ■Automatic tuning ■Manual tuning Presetting stations ■Automatically presetting stations (for FM stations) ■Manually presetting stations Exchanging preset stations Tuning in to a preset station RECEIVING RDS STATIONS (U.K. and Europe models only) Description of RDS data ■PTY (Program Type) mode: ■RT (Radio Text) mode: ■CT (Clock Time) mode: Changing the RDS mode PTY SEEK function ■To cancel the steps 1 or Setting the manufacturer code Other component controlling functions Controlling a DVD player SET MENU List of SET MENU items Adjusting the items on the SET MENU settings) ■1A CENTER (center speaker mode) ■1B FRONT (front speaker mode) ■1C REAR LR (rear speaker mode) ■1D BASS (LFE/bass out mode) 2 LFE LEVEL 3 SP DLY TIME (speaker delay time) 4 D. RANGE (dynamic range) 6HP TONE CTRL (headphone tone control) 7 INPUT MODE (initial input mode) 8 DISPLAY SET (brightness of front panel display) ■DIMMER ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS ■For 5ch Stereo Adjusting the delay time Adjusting the parameter settings for PRO LOGIC II Music ■Changing parameter settings ■PRO LOGIC II Music parameter descriptions TROUBLESHOOTING ■General Page ■Tuner ■Remote control GLOSSARY SPECIFICATIONS LIST OF MANUFACTURER’S CODES DVD Page (NX-S80S)