Yamaha AVX-S80 TROUBLESHOOTING, ■General

TROUBLESHOOTING

Refer to the chart below when this system does not function properly. If the problem you are having is not listed below or if the instruction below does not help, set this system to the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center.

■General

	Problem					Cause	Remedy	Refer
								to page

	This system fails to					The power cord is not connected or the plug	Firmly connect the power cord.	—
	turn on when					is not completely inserted.
	STANDBY/ON (or
	POWER (				) is
	pressed, or enters in					This system has been exposed to a strong	Set this system in the standby mode, disconnect	—
	the standby mode					external electric shock (such as lightning and	the power cord, plug it back in after 30 seconds,
	soon after the power					strong static electricity).	then start operating.
	has been turned on.

	No sound.					Incorrect input or output cable connections.	Connect the cables properly. If the problem	12 – 17
							persists, the cables may be defective.

						An appropriate input source has not been	Select an appropriate input source with the	19
						selected.	input selector buttons.

						The speaker connections are not secure.	Secure the connections.	15 – 16

						The volume is turned down.	Turn up the volume.	19

						The sound is muted.	Press MUTE or any operation buttons of this	19
							system to cancel a mute and adjust the volume.

						The source that this system cannot reproduce,	Play a source whose signals this system can	—
						such as a CD-ROM, is being played.	reproduce.

	The sound suddenly					The sleep timer has functioned.	Turn on the power, and play the source again.	20
	goes off.

	Only the speaker on					Incorrect cable connections.	Connect the cables properly. If the problem	15 – 16
	one side can be						persists, the cables may be defective.
	heard.

	Sound can be heard					The sound effect is off.	Press STEREO to turn it on.	25
	only from the front
	only from the front					A Dolby Surround, Dolby Digital or DTS	Select another DSP program.	21 – 22
	speakers.					A Dolby Surround, Dolby Digital or DTS	Select another DSP program.	21 – 22
	speakers.					decoding DSP program is being used with
						decoding DSP program is being used with
						material not encoded with Dolby Surround,
						Dolby Digital or DTS.

						A 96-kHz sampling digital signal is being	When a 96-kHz sampling digital signal is being	25
						input to this system.	input to this system, sound is output from the
							front speakers only.

APPENDIX

English

43

Contents

HOME THEATER SOUND SYSTEM IMPORTANT SAFETY INSTRUCTIONS CAUTION FCC INFORMATION (for US customers) We Want You Listening For A Lifetime CONTENTS INTRODUCTION FEATURES ■About this manual CHECKING THE ACCESSORIES INSTALLING BATTERIES IN THE REMOTE CONTROL ■Notes on batteries CONTROLS AND FUNCTIONS Front panel Remote control ■Using the remote control Front panel display PREPARATION STEPS SPEAKER SETUP Speaker placement Installing the speakers ■Placing the center speaker ■Placing the front and rear speakers ■Mounting the front and rear speakers on a wall ■If you want to mount a speaker on a commercially available speaker stand CONNECTIONS components ■Types of audio jacks ■Type of video jacks ■The connection example Connecting the antennas ■Connecting indoor FM antenna ■Connecting the AM loop antenna Connecting the speakers ■Using commercially available speakers and speaker cables Connecting to an external amplifier Connecting the AC power cord ■ Memory back-up Turning on the power ADJUSTING SPEAKER OUTPUT LEVELS Using the test tone BASIC PLAYBACK Basic operations ■Enhancing the bass tones ■To mute the sound ■When you have finished using this system ■Setting the sleep timer ■Input modes and indications Selecting a sound field program ■Feature of DSP programs Page ■Table of Program Names for Each Input Format ■Selecting PRO LOGIC ■Playing Dolby Digital Surround EX or DTS ES software ■Virtual CINEMA DSP ■SILENT CINEMA DSP ■Normal Stereo Reproduction ■Displaying the information about input signal ■About 96-kHzsampling digital signals RECORDING ■Timer playback/recording TUNING Automatic and manual tuning ■Automatic tuning ■Manual tuning Presetting stations ■Automatically presetting stations (for FM stations) ■Manually presetting stations Exchanging preset stations Tuning in to a preset station RECEIVING RDS STATIONS (U.K. and Europe models only) Description of RDS data ■PTY (Program Type) mode: ■RT (Radio Text) mode: ■CT (Clock Time) mode: Changing the RDS mode PTY SEEK function ■To cancel the steps 1 or Setting the manufacturer code Other component controlling functions Controlling a DVD player SET MENU List of SET MENU items Adjusting the items on the SET MENU settings) ■1A CENTER (center speaker mode) ■1B FRONT (front speaker mode) ■1C REAR LR (rear speaker mode) ■1D BASS (LFE/bass out mode) 2 LFE LEVEL 3 SP DLY TIME (speaker delay time) 4 D. RANGE (dynamic range) 6HP TONE CTRL (headphone tone control) 7 INPUT MODE (initial input mode) 8 DISPLAY SET (brightness of front panel display) ■DIMMER ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS ■For 5ch Stereo Adjusting the delay time Adjusting the parameter settings for PRO LOGIC II Music ■Changing parameter settings ■PRO LOGIC II Music parameter descriptions TROUBLESHOOTING ■General Page ■Tuner ■Remote control GLOSSARY SPECIFICATIONS LIST OF MANUFACTURER’S CODES DVD Page (NX-S80S)