CONTROLS AND THEIR FUNCTIONS

FRONT PANEL

1

2

3

4

5

6

7 8

9

0

 

NATURAL SOUND STEREO AMPLIFIER AX 392

 

 

 

 

 

 

 

 

 

 

 

 

 

 

l

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SLEEP

AUX

TAPE

MD

CD TUNER PHONO

TAPE MONITOR

CD DIRECT AMP

 

 

 

 

 

 

 

 

 

 

 

 

INPUT

 

VOLUME

 

 

 

 

 

 

 

 

 

 

 

 

 

20

l6

 

 

 

 

 

 

 

 

 

 

 

 

 

l2

 

 

 

 

 

 

 

 

 

 

 

 

28

 

8

STANDBY/ON

 

l

0 l

l 0

l

l

0 l

l FLAT

–30dB

 

 

 

 

 

 

 

2

2

2

2

2

2

2

l0

 

 

 

 

 

 

 

3

3

3

3

3

3

3

9

 

 

40

 

4

 

 

4

4

4

4

4

4

4

8

 

 

 

 

 

 

 

5

5

5

5

L 5

5 R

5 6 7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

60

 

2

 

 

BASS

TREBLE

BALANCE

LOUDNESS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

–dB

PHONES

SPEAKERS

 

 

 

 

 

 

 

 

 

 

 

 

 

A

B

 

 

 

 

 

 

 

 

 

 

 

 

 

ON

OFF

 

 

 

 

 

 

 

 

 

 

 

 

A B C D

1STANDBY/ON switch

Press this switch to turn the power to this unit on. Press it again to turn this unit into the standby mode.

Standby mode

In this state, this unit consumes a very small quantity of power to receive infrared-signals from the remote control transmitter.

2Power indicator

Lights up while the power to this unit is on.

3Remote control sensor

Receives signals from the remote control transmitter.

4SLEEP indicator

Lights up while the built-in SLEEP timer is functioning.

5Input source indicators

The indicator for the source selected by the INPUT selector lights up.

6TAPE MONITOR indicator

Lights up while the TAPE MONITOR switch is on.

*When the tape deck (TAPE) is selected as the input source, this indicator will not light up even if the TAPE MONITOR switch is on.

EF

7TAPE MONITOR switch

When the tape deck connected to the TAPE terminals on the rear of this unit is used for recording, you can monitor the sounds being recorded by pressing TAPE MONITOR so that TAPE MONITOR indicator lights up.

8INPUT selector

When turned, selects a program source to listen to.

The input source indicator for the currently selected source lights up.

9CD DIRECT AMP switch

Press this switch inward to listen to a CD source in the purest sound. (Refer to page 13 for details.)

0VOLUME control

Used to raise or lower the volume level.

APHONES jack

PHONES

 

When you listen with headphones,

 

connect the headphones to the

 

PHONES jack.

 

When listening with headphones

 

privately, set both the SPEAKERS

 

A and B switches to the OFF

 

position.

 

8