Yamaha DVD-S1200 Speaker setting, (R), (R), Rear, Note, Note, SETUP, Cursor, Large:, Small:, Main (L), Main (R), (L) a (L) c, buttons/ENTER, press [ENTER], ³Rear speakers

Advanced operations

AUDIO/VIDEO

POWEROPEN/CLOSE

Í/ I

	1	2	3	4
	5	6	7	8
				CANCEL
	9	0	S10
	SET UP			MARKER
	VIDEO OFF GROUP		PAGE	TEXT
	TOP MENU			MENU
	DIRECT NAVI			PLAY LIST	Cursor
		ENTER
	ON SCREEN			RETURN	buttons/ENTER
	PLAY MODE SUBTITLE		AUDIO ANGLE
Main (L)			Center		Main (R)
a		b a c			a
SETUP
Exit	L	ms	C	dB	R
		0		0
	Exit			dB	SW
	Test
				0
SELECT
Test	LS	dB	ms dB		RS
signal ENTER RETURN		0	0	0
		Rear			Subwoofer
(L) a (L) c			b (R) c (R) a c a
A
		LS			LS
No	Large			Small
B
L	C			R
	d	e
			SW
		f
LS		RS
³Center speaker
Difference				Setting
Approx. 50 cm (11/2 feet)				1.3 ms
Approx. 100 cm (3 feet)				2.6 ms
Approx. 150 cm (5 feet)				3.9 ms
Approx. 200 cm (6 feet)				5.3 ms
³Rear speakers
Difference				Setting
Approx. 200 cm (6 feet)				5.3 ms
Approx. 400 cm (12 feet)				10.6 ms
Approx. 600 cm (18 feet)				15.9 ms

Changing settings

Speaker setting

[DVD-A] [DVD-V]

Change speaker size and presence =, delay time >, and channel balance ? to suit the speakers you have connected.

These settings are not necessary when you select “2-channel” (only two speakers are connected).

Speaker presence and size (=)1.Press the cursor buttons [3, 4, 2, 1] to select the item and press [ENTER].2.Press the cursor buttons [3, 4] to select the setting andpress [ENTER].

Icon examples: Rear speaker (L) [A]

Large: When the speaker supports low-frequency (under 100 Hz) reproduction.

Small: Select when the speaker does not support low-frequency reproduction.

The size setting for the main speakers is automatically determined by the setting for the subwoofer.

»	Delay time (>)
B

[DVD-V](Dolby Digital, center and rear speakers only)

For optimum listening with 5.1-channel sound, all the speakers, except for the subwoofer, should be the same distance from the seating position. If you have to place the center or rear speakers closer to the seating position, adjust the delay time to make up for the dif- ference.

If distance @ (from the center speaker) and B (from the rear speak- ers) are the same as or greater than A (from the main speakers), leave the delay time as “0”, the factory preset.

If either distance @ or B is less than A, find the difference in the relevant table and change to the recommended setting.

Changing the delay time

1.Press the cursor buttons [3, 4, 2, 1] to select the delay time box and press [ENTER].

2.Press the cursor buttons [3, 4] to adjust the delay time and press [ENTER].Speaker balance (?)1.Press the cursor buttons [3, 4, 2, 1] to select “Test” and press [ENTER].

A test signal is output from one speaker at a time, starting with the main left speaker and proceeding clockwise.

MAIN (L)>CENTER>MAIN (R)

:;

REAR (L)(-----------==REAR (R)

2.While listening to the test signal, press the cursor buttons [3, 4] to adjust the volume of the center and rear speakers so they are the same apparent volume as the main speakers (s6 dB to r6 dB).

(The main speakers cannot be adjusted here.)

3.Press [ENTER].

The test signal stops.

Note

³Test signal is effective only when you made analog connection. When you make digital connection, make adjustment using the test tone on the amplifier.

³No signal is output for the subwoofer. To adjust its volume, play something, then return to this screen to adjust to suit your taste.

When you are finished

Press the cursor buttons [3, 4, 2, 1] to select “Exit” and press [ENTER].

Note

The unit may be unable to output as set here due to limitations imposed by the unit itself or the disc being played. (The FL display’s “P.PCM” indicator lights or “D.MIX” indicator goes out in these cases.)

32