Yamaha EM5014C Y, Z, [, \, ], ^, a, b, c

Front & Rear Panels

EMX5014C Owner’s Manual 25

Reference

YMaximum Output Switch

This selector lets you set the maximum output from for

the 2-channel internal amp to any of three levels. Set

this to match the size of your room or the input capac-

ity of your speakers.

500W: Maximum 500W + 500W/4 ohms.

200W: Maximum 200W + 200W/4 ohms.

75W: Maximum 75W + 75W/4 ohms

ZPOWER AMP Switch

Selects the output that gets sent to the SPEAKERS

jacks, as follows.

L/R:

SPEAKERS jacks A1 and A2 output the signal from

the Stereo L bus, while jacks B1 and B2 output the sig-

nal from the Stereo R bus. The overall volume is

adjusted by the ST master fader.

AUX1/MONO:

SPEAKERS jacks A1 and A2 output the signal from

the AUX 1 bus; the volume for this signal can be

adjusted using the AUX1 fader. SPEAKERS jacks B1

and B2 output the mix of the signals on the Stereo L

and R buses; the volume can be adjusted with the ST

master fader.

AUX1/AUX2:

SPEAKERS jacks A1 and A2 output the signal from

the AUX 1 bus, while jacks B1 and B2 output the sig-

nal from the AUX2 bus. Volumes can be adjusted using

the AUX1 and AUX2 faders, respectively.

[YS Processing Switch

This switch turns Yamaha Speaker Processing on or

off. The processor adjusts the speaker’s bass ranges so

as to compensate, for example, for a lack of subwoof-

ers. Note however that the resulting frequency balance

may vary according to the speakers you are using.

\PHANTOM Switch and Indicator

This switch toggles phantom power on and off. The

indicator lights up when the setting is on. If you set the

switch on, the mixer supplies power to the XLR mic

input jacks on all channels (the INPUT B jacks on

channels 1 to 6, and the MIC jacks on channel pairs

7/8 to 9/10). Set this switch on when using one or more

condenser microphones.

When the switch is on, the mixer supplies DC +48V

power to pins 2 and 3 of all XLR input jacks.

•Be sure to leave this switch off if you do not need

phantom power.

•When using phantom power, do not connect any

devices other than condenser microphones to the

XLR input jacks. Other devices may be damaged

if connected to phantom power. This precaution

does not apply to balanced dynamic microphones,

however, as these will not be affected by phantom

power.

•To avoid damage to speakers, be sure to turn off

the power to the EMX itself and to any other

power ampliﬁers and power speakers before

switching phantom power on or off. We also rec-

ommend that you turn all output controls (channel

faders, ST Master fader, AUX1/2 faders, etc.) to

minimum settings before operating the switch, to

avoid risk of loud noises that could cause hearing

loss or device damage.

]STANDBY Switch

This switch mutes the input to channels 1 to 6. The

switch lights up to indicate that the mute has been

turned on. Note that the mute does not work on chan-

nels 7/8 to 13/14.

When using the mixer for live performances, you can

ﬁll in gaps in the performance by turning on the

standby switch and feeding background music from a

CD player or other such device into channels 7/8 to

13/14.

^LEVEL Meters

If the ST/AFL-PFL switch a is set to ST, these meters

show the L and R levels of the signal output from the

ST OUT jacks S. If the ST/AFL-PFL switch is set to

AFL-PFL, the meters show the levels output from the

PHONES jack T.

Note that the signal output to the ST OUT jacks is

also passed through the internal ampliﬁer and then

output at the SPEAKERS jacks h. Keep an eye on

the LIMITER lamps X to ensure that the level at the

SPEAKERS jacks does not stay too high.

aST/AFL-PFL Switch

If the switch is set to AFL-PFL ( ), the LEVEL

meters show the level of the output at the PHONES

jack prior to adjustment by the PHONES control. If the

switch is set to ST ( ), the meters show the level

output at the ST OUT jacks following adjustment by

the ST master fader.

The PFL (G, N, d) and AFL e switches select the

mix to be monitored at the PHONES jack.

bPHONES Control

Controls the level of the signal output to the PHONES

jack.

cST SUB OUT Control

Adjusts the signal level to the ST SUB OUT jacks.

Has no effect on the output from the ST OUT and

SPEAKERS jacks.

NOTE