Manuals / Brands / Home Audio / CD Player / Yamaha / Home Audio / CD Player

Yamaha EMX-220VCD Adjusting brightness of the display, Adjusting input level of sources respectively, value: ±0), Control range, (Selectable values: 0 dB, –3dB, –6dB, –9dB)

1 58

Download 58 pages, 1.31 Mb

ADJUSTMENTS

1

DISPLAY

VOLUME

2

DISPLAY

Adjusting brightness of the display

If desired, you can adjust brightness of the display.

1 Press and hold the DISPLAY button for more than 2 seconds so that “DIMMER±0” appears on the display.

2 Holding the DISPLAY button pressed, turn the VOLUME control clockwise to increase or counterclockwise to decrease brightness.

This adjustment can be made even though this unit is in the standby mode.Control rangeWhen the power is on: ±0 to –6 (Preset value: ±0)When this unit is in the standby mode : +3 to –3 (Presetvalue: ±0)

Adjusting input level of sources respectively

English

1

INPUT SELECTOR

VCD/CD TUNER

You can adjust input level of sources (the built-in Video CD player, tuner, and external units connected to this unit, for example tape deck and video cassette recorder).

VCR•LD/TV•VCD/CD•TAPE/MD•TUNER

2	INPUT TRIM

3

VOLUME

INPUT TRIM

(Selectable values: 0 dB, –3 dB, –6 dB, –9 dB)

1 Select a source whose input level you will adjust by using the INPUT SELECTOR buttons, and then play back the source. (For source playback, refer to pages 18 to 33 ).

2 Press and hold the INPUT TRIM button for more than 2 seconds so that “TRIM” and the currently selected value appear on the display.

3 While holding the INPUT TRIM button down, change the value by turning the VOLUME control.

4 When you finish the adjustment, release the INPUT TRIM button.(The selected value is memorized by this operation.)5 In the same way, adjust input level of other sources.

E-15

Contents

Page SUPPLIED ACCESSORIES After unpacking, check that the following parts are contained ACCESORIOS INCLUIDOS Remote control transmitter AM loop antenna 90 A B C D E F G H IJ K L MN OP Q R S T U V W JK L MN Q R S 0.2 m – 6 m (8” – 20’) Rear speakers Altavoces traseros Center speaker Altavoz central Front speakers White line Linea blanca LD player etc Monitor TV Tocadiscos de discos láser, etc Monitor de TV INTRODUCTION CONTENTS Page PRECAUTIONS TUNING OPERATION PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT ■Do not operate this unit upside-down.It may overheat, possibly causing damage ■Never open the cabinet. If something drops into the set, contact your dealer ■For Singapore model : To eliminate condensation: NOTE CAUTION FOR CARRYING THIS UNIT CAUTION FOR MOVING THIS UNIT VOLTAGE SELECTOR (China and General models only) Voltages are 110/120/220/240V AC, 50/60 Hz FEATURES General c5-SpeakerConfiguration Front L, R: 100W + 100W (6Ω ) RMS Output Power, 10% THD,1 kHz (See figure 1 on page 3 at the beginning part of this manual.) 1Preset Equalizer Mode Indicator (MUSIC) 2Sound Field Program Indicator (PROGRAM) 3Karaoke Mode Indicator (KARAOKE) 4Center Channel Mode (NOR/PHANTOM) Indicator (See figure 3 on page 5 at the beginning part of this manual.) 1Remote Control Transmitter Window 2Preset Station Number Buttons 3A, B, C, D, E Selector Buttons 4TUNER Input Selector Button Speaker configuration Speaker placement Good No good Only for customers who use the YAMAHA NS-P30speaker system (separate purchase) “NS-P30” ■Mounting the rear speakers (NX-E70) To hang in a side long way WARNING: ■Mounting the center speaker (NX-C70) Connecting speakers (See figure 6 on page 6.) (See figure 7 on page 7.) (1) (2) 15 m (49 feet) (4) (3) Connecting external components (See figure 8 on page 8.) Connecting the AC supply lead Turning this unit on or into the standby mode Volume control Listening with headphones Setting the clock Adjusting brightness of the display Adjusting input level of sources respectively (L and R) Press the VOLUME + (up) button to increase the volume Press the TEST button Speaker balance adjustment Before operation NORMAL (For 5-speaker configuration): Page Press the OPEN/CLOSE button to open the disc table VIDEO CD PLAYER OPERATION STANDBY/ON DISC selector buttons CD/Video CD playback *If you play back a Video CD, turn on the monitor TV connected to this unit 7 Press the play/pause / button to start playback from track For easier operation To interrupt playback 1 Press the play/pause / button * The “ ” indicator will flash Direct-selectionplayback A. For example, to choose selection Press the “5” button B. For example, to choose selection (1)Press the “+10” button To advance or reverse playback rapidly (Manual search) 1 Begin playback 2 Press and hold the button to advance playback rapidly, and the button to reverse playback rapidly Index search Program play You can program up to 20 tracks in any desired order 2 When in the stop mode, press the PROG button to prepare for programming “PROG” and 3 If necessary, select a desired disc by pressing the DISC SKIP button Random play 1 Load discs and close the disc table To cancel the random play cThis feature will not function during programming or program play (off) Repeat play Repeat play modes SINGLE REPEAT (S REP) FULL REPEAT (F REP) When the unit is in the all disc play mode: Switching the time display [Example] To cancel DIGEST and INTRO operations To get a quick overview of a track or a disc (for Video CDs only) To watch scenes of a selected track on a Video CD To watch the beginning of all tracks on a Video CD RETURN: RETURN button NEXT: NEXT button PREV: PREV 1, 2, 3, 4: Track number input Basic operation Use the remote control transmitter for making Playback Control operations To stop playback Press and hold the RETURN button for more than 2 seconds To return to a previous screen mode during playback Press the RETURN button once If the disc has index numbers TUNING OPERATION Automatic tuning 3 Press the AUTO/MAN’L button so that “AUTO” lights up on the display (In this mode, stations are received in stereo or monaural automatically.) 4 Press the button to tune to a higher frequency, or Manual preset tuning To store stations (Example: To store a station to A1) 2 Press the tuner MEMORY button *“MEMORY” and “PRESET” will flash on the display for about 5 seconds Automatic preset tuning When the automatic preset tuning is completed; To listen to or watch a source on an external unit connected with this unit To record a source to tape USING GRAPHIC EQUALIZER PROGRAM 100 1K 10K Preset graphic equalizer modes (MUSIC) Mode Adjusting the graphic equalizer for your desired sound taste Turning the equalizer to “flat” (the state with no equalization applied) Storing your own equalizer patterns USING SOUND FIELD PROCESSOR Listening to the music with a sound field effect PRO LOGIC 3 STEREO HAL OFFARENA MONO MOVIE STADIUM DISCO Adjusting CENTER LEVEL Adjusting REAR LEVEL Adjusting DELAY TIME KARAOKE OPERATION Singing karaoke 1 Connect one or two microphones to the MIC jack(s) on the front panel L R VOCAL CUT (off) Adjusting the level of echo effect Control range: On the front panel: On the remote control transmitter: Adjusting key level of the source currently played back To record: HOW TO USE THE BUILT-INTIMER Timer play 1 Prepare the source to be played For tuner: Tune in to the station you will listen to ➂ ON TIME/time setting mode STANDBY/ON HOUR MIN TIME ADJ TIMER ➃OFF TIME/time setting mode To cancel the timer play setting Sleep timer operation This unit can be turned into the standby mode automatically 3 Press the SLEEP button repeatedly until the desired sleep OFF SLEEP ↑ *The SLEEP indicator will light up to indicate that the sleep timer is on TROUBLESHOOTING SYMPTOM CAUSE REMEDY Page Video Printed in Malaysia