Yamaha MDX-595 TROUBLESHOOTING

TROUBLESHOOTING

If your MD recorder fails to operate normally, check the following table. It lists common operating errors and simple measures which you can take to correct the problem. If it cannot be corrected, or the symptom is not listed, disconnect the recorder’s power cord and contact your authorized YAMAHA dealer or service center for help.

Symptom		Cause		Remedy
The unit does not respond to	• MD is dirty or damaged.		• Replace the current disc with a new
operations.	• MD is damaged (“UTOC ERR appears			one.
		in the display).
It happens that this unit does not work	•	There is an influence of strong external	•	Turn the power off and disconnect the
normally.		noise (lightning, excessive static		AC power from the AC outlet. After
		electricity, etc.) or a misoperation was		about 30 seconds have passed,
		performed while using this unit.		connect the power and try again.
Playback is not possible.	• Moisture is on the laser pickup.		• Leave the unit switched ON and wait 20
				to 30 minutes for the moisture to
				evaporate before trying to play a disc.
	• The power is OFF.		• Press POWER to turn the power on.
	•	The disc has been loaded incorrectly.	•	Reload the disc with the label side
				facing up, and the arrow pointing
				toward the disc insertion slot.
	• An unrecorded (blank) MD was loaded		• Insert a recorded MD.
		(“Blank Disc” appears in the display) .
Recording is not possible.	• The disc is record protected		•	Slide the record-protect tab to the
		(“Protected” appears in the display).		closed position.
	• A pre-mastered MD is loaded		• Load a recordable MD.
		(“Playback MD” appears in the display).
	•	The source is not connected correctly.	•	Check all connections again.
	•	The input setting is incorrect.	•	Press INPUT repeatedly to select the
				correct input jacks.
	•	The recording level is too low.	•	Turn REC LEVEL to adjust the recording
				level.
	•	The digital output level of the digital	•	Set the digital output level of the digital
		source is too low.		source to “MAX”.
	• There is not enough blank space left on		• Load a recordable MD with fewer
		the MD.		recorded tracks, or erase unnecessary
				tracks from the current MD.
	•	If the power cord was unplugged or	•	If recording was interrupted, try
		there was a power outage during		recording again starting from the
		recording, that recording may be lost.		beginning.
The MD cannot be removed when	• The carriage lock function has activated.		•	Insert the MD completely, then press
partially inserted.				) EJECT to eject it.
Excessive noise.	•	The unit is too close to the television or	•	Place the unit farther away from the
		other component.		television or other component.
The remote control does not operate.	•	The batteries are exhausted.	•	Replace the batteries.
	•	The remote control transmitter is	•	Operate the remote from less than 6
		operated from an incorrect distance or		meters (about 20 feet) and within 30° on
		angle.		either side of the sensor.
	•	The remote control sensor is located in	•	Place the unit away from the strong
		strong direct light.		light.

To clean the cabinet

Use a soft cloth slightly moistened with mild detergent solution.

Care of MDs

•Do not expose the MD to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be a considerable rise in temperature inside the car.

•Periodically remove dust and debris from the cartridge surface by wiping it with a dry cloth.

•Because the MD itself is housed in a cartridge, you can handle it normally without being concerned about dirt or fingerprints. However, malfunctioning may result if the cartridge itself is dirty or warped.

Do not open the shutter on the MD cartridge

Trying to force the shutter open will damage the shutter.

English

27